Miller Electric and DS-74DX16 Auxiliary Menus Continued, Reset To Factory Settings, Arc Time

5-12. Auxiliary Menus
						1	Program Display
						2	Program Push Button
						3	Sequence Push Button
				4		4	Upper Display
						5 Upper Display Push Button
					5	6	Lower Display
1						7	Lower Display Push Button
						8	Adjust Control
					7	9	Setup Push Button
2
	Program	Volts	Time (sec)
		Wire Speed		Amps	6
	Start
	Crater			Trigger Hold
	Pre/Postflow			Dual Schedule	9
3
	Sequence		Adjust	Setup
				8

5-12 Auxiliary Menus (Continued)

Reset To Factory Settings	power source min and max voltage preset	The upper display shows “PSS”. Lower dis-
A reset menu is displayed if the following four	range. The minimum voltage is displayed in	play shows “On” or “Off”. The Adjust Control is
	the upper display and the lower display indi-	used to select either “On” or “Off”.
push buttons are pressed simultaneously:
	cates “VMIN”. When the Setup push button
Program, Sequence, upper display, and Set-		Arc Time
	is pressed the unit displays the maximum
up. The upper display indicates “WIPE” . The
	voltage setting of the welding power source.	• If the Setup push button is pressed, the unit
lower display indicates “OFF”. The lower push
	The maximum voltage is displayed in the up-	displays arc time in hours.
button is active indicating that the Adjust con-
	per display and the lower display indicates
trol can be used to change the unit to “WIPE		Arc time is indicated by the Program display
	“VMAX”.
ON”. When “WIPE ON” is set, if the original		showing “HR”. Arc time is shown in the lower
four push buttons are simultaneously pressed	In both cases, the Adjust control is used to	display.
a second time, the unit will reset all settings to	specify the minimum and maximum voltage	Cycles
factory default except the arc time and arc
	settings of the welding power source. The set-
cycle counts. If a reset is not desired, set the		• If the Setup push button is pressed, the unit
	tings correspond to arc voltage obtained at
display to “WIPE OFF” and simultaneously	minimum command and arc voltage obtained	displays the number of cycles.
press the Program, Sequence, upper display,	at maximum command.	Arc cycles are indicated by the Program dis-
and Setup push buttons to exit the reset menu.
Auxiliary Menu	This method of setting “VMIN” and “VMAX”	play showing “CL”. The arc cycle count is
		shown in the lower display.
	may be used if the power source being used
• An auxiliary menu is provided if both the Se-
	is not listed in the Power Source Selection	Run-In
quence and Setup push buttons are pressed	Menu.	• If the Setup button is pressed, the unit allows
simultaneously. The Setup push button and
sequence push button LEDS flash when the	. If a default power source has already been	setting the run-in modes. The run-in modes
		are program specific. Each program may be
auxiliary menu is displayed.	selected with the Power Source Selection
		set to its own run-in mode.
Pushing the Setup push button will step	menu, setting “VMIN” and “VMAX” will
		The upper display indicates “RUNI”. The
through the menu. Pushing the sequence	override the default power source set-
push button will step through the menu in re-	tings.	lower display indicates “AUTO”, meaning the
verse.		factory set automatic run-in speed is se-
. The auxiliary menu may be exited at any	. The power source selection menu must	lected.
		Pressing the lower display button allows a
time by pressing both the Sequence push	be set to “OFF” when overriding the de-
	fault “VMIN” or “VMAX” settings.	manual setting the run-in wire speed. Speed
button and the Setup push buttons simul-
		may be adjusted from 10% to 100% of weld
taneously.	Power Source Selection Menu
		wire speed.
V-Min And V-Max	• If the Setup push button is pressed, the unit	Pressing the lower display button allows dis-
• If the Setup push button is pressed, the unit
	allows the Power Source Selection menu to	abling of the run-in feature. When the lower
allows the setting of the manual override	be disabled or enabled.	display indicates “OFF” run-in is disabled.

OM-1500-14 Page 25