Manuals / Miller Electric / Power Tools / Welder

Miller Electric XMS 4000 manual Setup Push Button And Advanced Programming

Models: XMS 4000

1 40

Download 40 pages 734 b

Page 23

4-8. Setting And Using Weld Parameters From Memory (TIG and STICK Only)

. Check memory parameter for proper settings before the

		selections.
		Four memory selections are avail-
		able for each welding process (20
		total).
	P1	These memory selections provide
	P1	quick changes to welding pro-
		quick changes to welding pro-
		cesses with preset parameter val-
		ues. All memory selections have
		factory set defaults and may re-
		quire changes for the desired weld
		characteristics.
		Press P1 until desired memory
		selection LED illuminates.

4-9. Setup Push Button And Advanced Programming

P2

Press P2 to enter SET UP menu.

SET UP will appear on D1 and D2 only mo- mentarily and then change to the selected process parameter values.

Setup allows viewing and changing default parameter values for all welding processes for the desired weld characteristics.

D1 shows the welding parameter.

D2 shows the parameter value.

E1 changes the welding parameter.

E2 changes the parameter value.

.Incorrect settings in any process can

result in a program with undesirable weld characteristics. Setup should only be used by operators familiar with various welding processes and pa- rameters.

Pressing P2 again allows changing wire type selections (see Section 4-4).

Setting Menu Type (TIG and STICK only)

.MENU EASY only shows basic pa-

rameters for welding processes. MENU FULL shows all parameters for welding processes.

To set menu type, proceed as follows: Press P2 to enter SET UP menu.

Use E1 to select MENU EASY on D1 and D2 (default setting).

Use E2 to change D2 to FULL.

OM-224 043 Page 19

Image 23

Miller Electric XMS 4000 manual Setup Push Button And Advanced Programming, Setting Menu Type TIG and Stick only

Contents

Xmsr From Miller to You Table of Contents Declaration of Conformity for European Community CE Products Arc Welding Hazards Symbol UsageMarks a special safety message Magnetic Fields can affect pacemakers ARC Rays can burn eyes and skinFire or Explosion hazard California Proposition 65 WarningsAbout Pacemakers Principal Safety StandardsEMF Information Manufacturer’s Warning Label Definitions − Definitions60 s 100 h. std I1eff Manufacturer’s Rating Labels Symbols And DefinitionsI1max Duty Cycle And Overheating − InstallationSpecifications Volt-Ampere Curves Remove wire spool Turntable ScrewLocation Dimensions and WeightMovement Do not move or operate unit where it could tip Selecting a Location120 m Weld Output Terminals And Selecting Cable SizesRemote 7 Receptacle Information TIG And Stick Only ARC Welding can cause Electromagnetic InterferenceFilling Coolant Tank Circuit Breakers= GND/PE Electrical Service GuideConnecting Input Power 50/60 Hz Three PhaseFront Panel Controls − OperationWelding Process Selection Switching On the Unit and Recalling Factory ParametersBe aware that the wire type selection is Gas Selection in Synergic MIG or Synergic Pulsed MIG Welding Trigger Mode Selection TIG and Stick OnlySetting Menu Type TIG and Stick only Setup Push Button And Advanced ProgrammingSelecting Manual MIG Welding During SettingSetting Cooler Status Preparing Unit For MIG WeldingDuring Synergic MIG Welding Setting Cooler Status see SectionSelecting Synergic MIG Welding Selecting Synergic Pulsed MIG Welding Preparing Unit For TIG Welding Setting Initial And Final Amperage only in Menu FullSetting Postflow only in Menu Full Setting Cooler Status only in Menu FullPreparing Unit For Stick Welding TIG Lift-Arc WeldingMonths − Maintenance & TroubleshootingHelp Displays Do not remove case when blowing out inside of unitBlowing Out Inside Of Unit Is displayed TroubleshootingSoftware problems OM-224 043 − Electrical Diagram Unit Outer Assembly − Parts ListDia Part Description Quantity Mkgs Unit Main Assembly CR5,6,R1 Page Effective January 1 ITW Welding Products Italy S.r.l. Via Privata Iseo, 6/E Owner’s Record