Manuals / Minolta / Photography / Camera Flash

Minolta Complete Guide to the Flash with Model 5600HS Features

Models: 5600HS (D)

1 41

Download 41 pages 28.61 Kb

Page 8

ATTACHING AND REMOVAL

Attaching To The Camera

Push the mounting foot firmly onto the camera until it stops.

•The flash is locked in place automati- cally.

•If the built-in flash in the camera is

protruding, lower it before fitting the flash unit.

Removing From The Camera

While pressing the mounting-foot release button , remove the flash .

AUTO POWER ON/OFF AND FILM

	Auto Power On	PREPARATION
	Power is supplied to this flash automatically (auto power on) in the	PREPARATION

	following situations.
	• When the camera is used with the flash
	attached.
	• When the flash on/off button is pressed.
	Flash on/off button

Auto Power Off

Power is switched off and data panel indicators disappear automati- cally to save the batteries when the camera or flash is not used for four minutes (auto power off).

• When the flash is switched off (right diagram), the data panel indicator will disappear after eight seconds, or after 60 minutes in the case of wireless flash (p. 40).

•Custom settings may be used to change the

time of auto power off, or to disable auto power off (p. 65).

Film

Do not use high-speed film (rating in excess of ISO 1000) with TTL

direct metering ( displayed on the data panel, p. 36). Use of such film increases the exposure error.

•The low-speed film limit is the same as that for the films specified for the camera. See the camera manual for details.

14

15

Image 8

Minolta 5600HS (D) appendix Attaching and Removal, Auto Power ON/OFF and Film

Contents

Program Flash Maxxum Flash Applications AppendixFor Proper and Safe USE Contents Flash Units Cameras and Flash UnitsCameras Flash Unit Diagram Control Panel Names of PartsNames of Parts Data PanelChecking Batteries Installing BatteriesChamber Close the battery-chamber door Auto Power ON/OFF and Film Attaching and RemovalMode Flash the Basics Press the shutter-release butTon partway down and check That the subject is within Flash rangeMode Flash the Basics Exposure ModesSet the aperture and focus the subject Set the shutter speed, and focus the subjectExposure Modes Set the aperture and shutter speed, and focus the sub- jectZoom Zoom Flash CoverageAuto Zoom Zoom Flash Coverage Manual ZoomBuilt-In Wide Angle Adapter 17mm zoom angle Pull out the adapterFlash once at the set light level Level 1/1~1/32 Hold The setting prevents mis-operationTEST-FLASH/MODELING Flash Flash may be set to the following angles Bounce FlashFlash Adjusting Bounce Angle Bounce FlashData Panel Illuminator AF IlluminatorPress the data panel illuminator Illuminates the data panel at low-light levelsMode and Select Buttons MODE/SELECT ButtonPress the + or button to select the power level to be set Manual Flash MHIGH-SPEED Sync HSS PlayPanel HSSWIRELESS/REMOTE Flash Mode Types Of Wireless/Remote FlashUsing the built-in flash p Using two flash units pWIRELESS/REMOTE Flash Mode Using the Wireless Remote Flash Controller pWireless Flash Range Following two modes are avail- ableWIRELESS/REMOTE Flash Mode Using The Built-In Flash Set the camera to wireless flashSetting Wireless/Remote Flash By Flash Only Check that the built-in flash 5600HS D are fully chargedUsing Two Flash Units Setting Up The ControllerSetting Up The Off-Camera Flash Switch the 5600HS D onCheck that both flash units are fully charged Use test flash to check the off-camera flashPress the select button Taking PhotosUsing Wireless Remote Flash Controller Ratio-Flash Control Using Two Or More Flash UnitsUsing 5600HS D, 5400HS, 5400xi only Refer to the Wireless Remote Flash Controller manualPress the select button Using with 3600HS D or Set up the 5600HS D with the wireless ratio off-camera flashConnecting Camera and Flash by Cable Equalizing The Power Level Of All Flash UnitsConnecting by Cable All the flash units in a and B group can be usedPower level for the flash can be adjusted Setting Power Level LevelPower Level Press the + or button to Select the number of flashes Multiple Flash MultiPress the select button to blink Multiple Flash Multi Press the select button to blink Level on the data panelPress the select button Set the shutter speed and aperture Maximum Number Of Continuous FlashesReset to Default Settings Custom FunctionPress the select button for Seconds Press the select button toPress the mode button Wireless channel settingTime to auto power off Time to auto power off when using wirelessUsing xi Series Single Lens Reflex Cameras Maxxum/Dynax 9xi, 7xi, 5xi, 3xi, SPxiUsing Early AF Series Single Lens Reflex Cameras Using APS Single Lens Reflex CamerasUsing Minolta Digital Cameras USE in Combination with Other ProductsAccessories AccessoriesTemperature MaintenanceDuring Photography BatteriesPerformance PerformanceMemo 9222-8841-11 P-B00X