PROGRAMMING EXAMPLES
6.7Parameter Writing Program Example
1)Program example which changes the Pr. 7 "acceleration time" setting of station 2 inverter to 3.0 seconds Acceleration time writing code number: 87H (hexadecimal)
Acceleration time set data: K30 (decimal)
For the parameter code numbers, refer to the inverter manual.
The reply code at the time of instruction code execution is set to D2. (Refer to page 32)
| M9036 |
|
|
|
|
|
|
|
| H | H | K4 | K | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
26 |
|
|
|
|
|
|
|
|
|
|
|
| FROM 0000 | 00E2 | M200 2 | |||
|
|
|
|
|
|
|
|
|
|
|
| |||||||
| X0000 X000F X0001 X0020 |
|
|
|
|
| ||||||||||||
36 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| PLS | M302 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
| M302 |
|
|
|
| Write setting |
|
|
|
|
| ||||||
43 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| SET | M303 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
| M303 |
|
|
|
|
|
|
|
|
|
|
| H |
| |||
45 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| MOV | 0087 | D100 | |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| K |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| MOV | 0030 | D101 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| H | H |
| K | |
|
|
|
|
|
|
|
|
|
|
|
|
| TO | 0000 |
| 01E6 | D100 | 2 |
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| SET | M115 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| H | H |
| K | |
|
| M215 |
|
|
|
|
|
|
| FROM 0000 | 02E6 | D2 | 1 | |||||
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| RST | M115 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| RST | M303 |
| M9036 |
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
| H | H | K4 | K | ||||||
87 |
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
| TO | 0000 |
| 0162 | M100 2 | ||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Reads the remote input (RX20 to RX3F) data of buffer memory to
Writes Pr. 7 write (87H) to RWw6 and acceleration time setting data (K30) to RWw7.
Switches on the instruction code execution request (RY2F).
Reads reply code (RWr6) to D2 when the instruction code execution completion (RX2F) switches on.
Switches off the instruction code execution request (RY2F).
Writes
Note: 1. For parameters having numbers 100 and later, change their link parameter extension settings (set them to other than 0000H).
2. For other functions, refer to the instruction codes (page 29).
39