Viewing video images (continued)
C. Projectiing images
Preparation:
•Remove the lens cap.
•Turn on the power of the connected equipment.
| POWER button/ |
|
| ||
| POWER indicator |
| |||
LAMP TEMP | POWER |
|
|
|
|
|
| Main power switch | |||
AC IN | MAIN |
|
|
|
|
| LENS SHIFT |
|
|
|
|
|
|
|
| Lens shift dial | |
DOWN |
| UP |
|
|
|
| ZOOM IN / UP |
|
| ZOOM IN, OUT buttons | |
|
|
|
| ||
FOCUS |
| FOCUS +/RIGHT | FOCUS +/- buttons | ||
ZOOM OUT / DOWN |
|
|
|
| |
AUTO |
|
|
|
|
|
POSITION SOURCE MENU/EXIT | ENTER |
|
|
| |
|
|
| SOURCE button | ||
|
|
| ON | STANDBY |
|
ON( )button |
|
| AUTO OFF | LIGHT | |
|
|
| |||
|
|
|
|
| |
SOURCE button |
|
| COMP | ||
| Video | BNC | |||
|
|
|
| ||
|
|
|
| 16:9 |
|
|
|
| Standard |
| ZOOM |
|
|
|
| MEM2 |
|
|
|
| MEM1 |
| MEM3 |
{, } button |
|
| ZOOM IN/UP |
| |
|
| FOCUS+/RIGHT | |||
$, % button |
|
| ENTER |
| |
|
|
| MENU ZOOM OUT/DOWN | ||
|
|
|
| BRIGHT | C.TEMP |
|
|
| CONT |
| |
|
|
|
|
| |
|
|
|
| COLOR | SHARP |
|
|
| TINT |
| |
|
|
|
|
| |
1.Turn the main power switch to on (or to the I position).
• When the main power switch is turned on, the POWER
indicator lights up red.
LAMP TEMP 
POWER
Lighting in red
•If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating and the POWER button may not work after the main power switch is turned on. (The POWER indicator blinks red.) After the fan stops rotating, press the power button to turn back on the POWER indicator.
2.Press the POWER button on the projector or ON (
) button on the remote control.
LAMP TEMP POWER |
| LAMP TEMP POWER | |
Blinking | After about | Lighting in | |
1 minute. | |||
in blue | blue | ||
|
Power can not be turned “OFF”.
•It may take about one minute for the lamp to light up.
•The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.
3.Select an input source.
•Press the SOURCE button on the projector or any of the SOURCE buttons (such as
•Switch the input source after an image is projected on the screen.
•Though it may take some time before an image is displayed on the screen depending on the type of the input signal, such symptom is not a malfunction.
•Images may not be projected in the correct position, depending on the type of the input signal. In such a case, press the AUTO POSITION button on the projector or the AUTO button on the remote control. (See Page 21.)
4.Adjust the position of the projector to keep an appropriate projection distance with which images are projected in their specified sizes.
5.Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See Page 11.)
•When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See Page 11.)
6.Adjust the size of the projected image by pressing the ZOOM IN or OUT button on the projector or the remote control.
7.Adjust the focus by pressing the FOCUS+ or FOCUS- button on the projector or the remote control.
8.Adjust the image position by turning the lens shift dial of the projector.
Repeat steps 4 to 8, if necessary.
