System Description | Motorola T3 Power Broadband specification

System Description

System Description

The T3 PowerBroadband system is designed primarily for hospitality, but useful in any high density MDU (multiple dwelling unit) such as long term healthcare or centrally wired apartments. The system is comprised of two primary components; a 25-port Switch and a CPE device (the WallPlate). Advanced networking features such as 802.1Q VLANs and QoS can be managed throughout the system, from the 25-port switch to each port on the WallPlate.

Adaptive Line Power

T3 PowerBroadband delivers operating power to the remote WallPlates.

MC-802 Wireless WallPlate	Line powered up to 300m (1000ft)
M2 Ethernet WallPlate	Line powered up to 600m (2000ft)

T3 PowerBroadband Switch

The T3 switch is installed in a centrally located phone room; where all the telephone wires converge. The T3 switch has 25 ports for downstream WallPlates, and 2 x GigE uplink ports.

T3 PowerBroadband Switch:

Physical

•17.50"(43.8mm) x 14.25" (36mm) x 1.75" (44mm). 11.5lbs (5.2Kg)

•Operating Temperature: 0 - 50 degrees Celsius, 5% to 90% NC

•Operating Power: 300W maximum under full load, 200W typical

Interfaces

•Uplink ports

oTwo 10/100/1000Mb autosensing, full duplex Ethernet ports via RJ45

•Downlink ports

o25 VDSL UTP ports via RJ21 telco connector

Layer-2 Networking Features

•802.1Q VLAN trunk ports

•802.1Q PVID per port

•Port-based Isolation VLANs

•QoS, 4 queues per port, classification by IP-TOS or L2-COS bit

•IGMP, Layer 2+ routing, proxy, FastLeave

•1024 entry MAC forwarding table

Management

•Telnet, Console, webUI, Syslog, SNMPv2c

•RADIUS authentication, Admin and User level login

•Security: L2 VLAN, IP ACL

M2 Ethernet WallPlate

The m2 Ethernet WallPlate has two 10/100Mb Ethernet ports, and a pass-through RJ11 phone connector. It is installed at the end-point where Ethernet service is desired. It operates over a standard 2-wire telephone line.

Motorola, Inc.	570510-001-00 rev A	Page 12 of 50

Image 12

Motorola T3 Power Broadband manual System Description, T3 PowerBroadband Switch, M2 Ethernet WallPlate, Adaptive Line Power

Contents

T3 PowerBroadband Page Regulatory Statements Model Number45225 Frequency of Operation FCC and ICRF Exposure Guidelines International Radio Frequency Interference Requirements- FCC Marking and European Economic Area EEA T2-2500 and T3 Switch M2 WallPlate Waste Electrical and Electronic Equipment Weee Commands and Syntax Quality of Service QoS Commands and Syntax Command HierarchyAdministrative Commands Show Commands Global Commands Command CompletionStyle Conventions Interface Range T3 PowerBroadband Switch Adaptive Line PowerSystem Description M2 Ethernet WallPlate MC-802 Wireless WallPlate Features of the MC-802 802.11b/g radio PhysicalM2 Ethernet WallPlate Physical Radio Hardware Model Numbers and DescriptionModel Numbers and Description for related Products Model Number Part Number Description Front View Rear ViewCross-Connect Connections Mounting Options M2 2 port Ethernet WallPlate LED Status LightsPage System Administration Management AccessCLI Configuration Script files Access Methods Configuration Files using the webUI File dir Http Menus Wireless WallPlate Firmware Reboot the Wireless WallPlate to activate the new softwareUpgrading the Firmware T3 Firmware Line Quality View System Configuration and Status Summary Startup Running Commit mode Reset to Default ConfigurationOther Configuration Help System config mode automanualmode Managing the Wireless WallPlates WallPlate Inventory and Firmware ImageShow remote inventory Show remote image IP Addresses Private IP address Public IP address Static IP address pool Configuring a Wlan Global Radio Commands Per-WLAN Commands Monitor the WLANs and radiosExpanded Statistics and Status Access Control Lists ACLs Ip access-list config 1 deny http Radius network authenticated login Authenticating Administrative AccessAuthenticating Clients using Configure the Radius Server WallPlate Installation Basic ConfigurationTools Required Components provided with the MC-802 WallPlate Components required to purchase Step Enable line power Determine which port is being installed Finish the installation Enable line power Vlan Specification 802.1Q VLANsVlan terminology Tagged Untagged Vlan commands Tag-based Vlan Mode Port-based Vlan Mode Web UI configuration Vlan General webUI Tag-based Vlan webUI Create/Delete VLANsSet Vlan Egress Rules Set Vlan Ingress Rules Port-based Vlan webUI Quality of Service QoS QoS commands and concepts Network qos interface queue interface-id mode mode Dynamic packet classification 802.1P bitQueue Commands QoS ExamplePacket Classification Packet transmission Line Status Line Current Line Current Value Watts Reference Appendix a Pin-out Assignments Fast Ethernet WallPlate ports Appendix B Hardware Specifications T3 PowerBroadbandM2 WallPlate MC-802 Wireless WallPlate