DMA Channel 0/1/3/5/6/7

MS-6788 ATX Mainboard

These items specify the bus that the system DMA (Direct Memory Access) channel is used.

The settings determine if AMIBIOS should remove a DMA from the available DMAs passed to devices that are configurable by the system BIOS. The avail- able DMA pool is determined by reading the ESCD NVRAM. If more DMAs must be removed from the pool, the end user can reserve the DMA by assigning an [ISA/EISA] setting to it.

3-18

Page 51

Image 51

MSI 848P NEO-V - Motherboard - ATX manual DMA Channel 0/1/3/5/6/7

Contents

865PE Neo2-V / 848P Neo-V Series FCC-B Radio Frequency Interference Statement Voir LA Notice D’INSTALLATION Avant DE Raccorder AU Reseau Revision Revision History Date Copyright NoticeTrademarks Revision History Technical Support Safety Instructions Contents Clear Cmos Jumper JBAT1 Getting Started Slots Mainboard SpecificationsChipset Main Memory LAN Optional DimensionOn-Board Peripherals Audio Chipset Mainboard Layout 848P Neo-V MS-6788 v2.X ATX Mainboard Hardware Setup SYSFAN1 , p.2-14 Quick Components Guide Then Example of CPU Core Speed Derivation ProcedureCentral Processing Unit CPU Memory Speed/CPU FSB Support Matrix CPU Installation Procedures for Socket Installing the CPU Fan Fan power cable DIMM1 DIMM2 MemoryIntroduction to DDR Sdram DDR Population Rules Dual-channel DDR Introduction Installing DDR Modules ATX1 Power SupplyATX 20-Pin Power Connector ATX1 ATX 12V Power Connector JPW1 PS/2 Mouse 6-pin Female PS/2 Keyboard 6-pin Female Mouse ConnectorKeyboard Connector Back Panel Serial Port Connector COM a USB ConnectorsSPDIF-out Port Connector MIC Audio Port ConnectorsLine Stereo Audio Connectors Line Out RJ-45 LAN Jack Parallel Port Connector LPT1 CD-In Connector CD1 ConnectorsFloppy Disk Drive Connector FDD1 Fan Power Connectors CPUFAN1/SYSFAN1 ATA100 Hard Disk Connectors IDE1 & IDE2 Front USB Connectors JUSB2 & JUSB3MSI Reminds You Serial ATA HDD Connectors SATA1, SATA2 SATA2SATA1 JSP1 Bracket Spdif Connector JSP1 Optional JFP1 JFP2 Front Panel Connectors JFP1 & JFP2 JAUD1 Front Panel Audio Connector JAUD1 Bracket 2 Connector JDB1 Optional JDB1Bracket Jumpers Clear Cmos Jumper JBAT1JBAT1 PCI Interrupt Request Routing SlotsAGP Accelerated Graphics Port Slot PCI Peripheral Component Interconnect Slots Bios Setup Selecting the First Boot Device Entering Setup Main Menu Default SettingsControl Keys Getting Help Main Menu Load Bios Setup Defaults Set Supervisor PasswordSet User Password Load High Performance Defaults Standard Cmos Features Floppy Drive a Advanced Bios Features A.R.T. for Hard Disks BootUp Num-LockPassword Check Boot To OS/2 CPU L1 & L2 Cache System Bios CacheableMPS Revision Apic Acpi SCI IRQ CAS# Latency Advanced Chipset FeaturesDram Timing Setting Configure Sdram Timing by SPD Burst Length RAS# to CAS# DelayPrecharge Delay RAS# Precharge Power Management Features Re-Call VGA Bios at S3 ResumingAcpi Standby State Set Monitor Events Power Management/APMPower Button Function Suspend Time Out Minute Resume On RTC Alarm Keyboard PowerOn FunctionSpecific Key for PowerOn Mouse PowerOn Function Init. Graphics Adapter Priority PNP/PCI ConfigurationsPCI Latency Timer PCI Clocks Clear Nvram Set DMAs to PnP or ISA PCI IDE BusMasterSet IRQs to PCI or ISA IRQ 3/4/5/7/9/10/11/14/15 DMA Channel 0/1/3/5/6/7 USB Controller On-Chip IDE ConfigurationOn-Chip ATAs Operate Mode Integrated Peripherals ATA Channel Selection ATA ConfigurationATA Keep Enabled Combined Mode Option Set Super I/O Parallel Port ModeOnBoard LAN AC’97 Audio EPP Version Parallel Port IRQParallel Port DMA Channel PC Health Status Dynamic OverClocking Frequency/Voltage Control Spread Spectrum Performance ModeCPU Ratio Selection Dram Frequency DDR Power Voltage Adjust CPU Bus Clock MhzAdjust AGP/PCI Clock Mhz CPU Vcore Adjust Set Supervisor/User Password Load High Performance/BIOS Setup Defaults