PC Health Status

BIOS Setup

This section shows the status of your CPU, fan, overall system status, etc. Monitor function is available only if there is hardware monitoring mechanism onboard.

CPU/System Temperature, CPU/System Fan Speed, Vcore, 3.3V, +5.0V, Battery, +5V SB

These items display the current status of all of the monitored hardware devices/ components such as CPU voltages, temperatures and all fans’ speeds.

3-23

Page 56

Image 56

MSI 848P NEO-V - Motherboard - ATX manual PC Health Status

Contents

865PE Neo2-V / 848P Neo-V Series Voir LA Notice D’INSTALLATION Avant DE Raccorder AU Reseau FCC-B Radio Frequency Interference Statement Copyright Notice TrademarksRevision History Revision Revision History Date Safety Instructions Technical Support Contents Clear Cmos Jumper JBAT1 Getting Started Mainboard Specifications ChipsetMain Memory Slots Dimension On-Board PeripheralsAudio LAN Optional Mainboard Layout Chipset 848P Neo-V MS-6788 v2.X ATX Mainboard Hardware Setup Quick Components Guide SYSFAN1 , p.2-14 Example of CPU Core Speed Derivation Procedure Central Processing Unit CPUMemory Speed/CPU FSB Support Matrix Then CPU Installation Procedures for Socket Installing the CPU Fan Fan power cable Memory Introduction to DDR SdramDDR Population Rules DIMM1 DIMM2 Installing DDR Modules Dual-channel DDR Introduction Power Supply ATX 20-Pin Power Connector ATX1ATX 12V Power Connector JPW1 ATX1 Mouse Connector Keyboard ConnectorBack Panel PS/2 Mouse 6-pin Female PS/2 Keyboard 6-pin Female SPDIF-out Port Connector Serial Port Connector COM aUSB Connectors Audio Port Connectors Line Stereo Audio Connectors Line OutRJ-45 LAN Jack MIC Parallel Port Connector LPT1 Connectors Floppy Disk Drive Connector FDD1Fan Power Connectors CPUFAN1/SYSFAN1 CD-In Connector CD1 MSI Reminds You ATA100 Hard Disk Connectors IDE1 & IDE2Front USB Connectors JUSB2 & JUSB3 SATA1 Serial ATA HDD Connectors SATA1, SATA2SATA2 Bracket Spdif Connector JSP1 Optional JSP1 Front Panel Connectors JFP1 & JFP2 JFP1 JFP2 Front Panel Audio Connector JAUD1 JAUD1 Bracket Bracket 2 Connector JDB1 OptionalJDB1 JBAT1 JumpersClear Cmos Jumper JBAT1 Slots AGP Accelerated Graphics Port SlotPCI Peripheral Component Interconnect Slots PCI Interrupt Request Routing Bios Setup Entering Setup Selecting the First Boot Device Default Settings Control KeysGetting Help Main Menu Main Menu Set Supervisor Password Set User PasswordLoad High Performance Defaults Load Bios Setup Defaults Standard Cmos Features Floppy Drive a Advanced Bios Features BootUp Num-Lock Password CheckBoot To OS/2 A.R.T. for Hard Disks System Bios Cacheable MPS RevisionApic Acpi SCI IRQ CPU L1 & L2 Cache Advanced Chipset Features Dram Timing SettingConfigure Sdram Timing by SPD CAS# Latency RAS# to CAS# Delay Precharge DelayRAS# Precharge Burst Length Acpi Standby State Power Management FeaturesRe-Call VGA Bios at S3 Resuming Power Management/APM Power Button FunctionSuspend Time Out Minute Set Monitor Events Keyboard PowerOn Function Specific Key for PowerOnMouse PowerOn Function Resume On RTC Alarm PNP/PCI Configurations PCI Latency Timer PCI ClocksClear Nvram Init. Graphics Adapter Priority PCI IDE BusMaster Set IRQs to PCI or ISAIRQ 3/4/5/7/9/10/11/14/15 Set DMAs to PnP or ISA DMA Channel 0/1/3/5/6/7 On-Chip IDE Configuration On-Chip ATAs Operate ModeIntegrated Peripherals USB Controller ATA Configuration ATA Keep EnabledCombined Mode Option ATA Channel Selection Parallel Port Mode OnBoard LANAC’97 Audio Set Super I/O Parallel Port DMA Channel EPP VersionParallel Port IRQ PC Health Status Frequency/Voltage Control Dynamic OverClocking Performance Mode CPU Ratio SelectionDram Frequency Spread Spectrum Adjust CPU Bus Clock Mhz Adjust AGP/PCI Clock MhzCPU Vcore Adjust DDR Power Voltage Set Supervisor/User Password Load High Performance/BIOS Setup Defaults