24

 

26

27

25

 

28

29

30

31

PUMP COMPONENTS

23

21

20

17

 

22

19

 

18

33

16

32

Figure 3-B. Pump

Components

Figure 3-B shows the location of the more components of the Dry Prime pump, The function of each component or control is described below:

16.Safety Chain – ALWAYS attach safety chain to the towing vehicle. NEVER tow the pump with the safety chain unattached! See towing section of this manual.

17.Towing Coupler/Ring – Attach this coupler to the towing vehicle. Use only the specified ball diameter as indicated on your coupler (2-5/16). Use of any other ball diameter will create an extremely dangerous condition which can result in separation of the coupler and ball or ball failure. A 3-inch tow ring is also available as an option.

18.Ajustable Tow Tongue – Tow tongue is adjustable by removing locking pin to adjust tongue length then reinserting pin to lock tongue in place.

19.Battery – Unit uses a +12VDC wet battery Group 31.

20.Engine – These pumps are equipped with either a Deutz F3L914 or F4L914 three or four cylinder air- cooled diesel engine.

21.Skid Lifting Bail –When lifting of the pump skid is required, attach a strap or chain of adequate lifting capacity to lift the skid.

22.Engine Control Box – Vandal proof (lockable) engine control box displaying engine guages, tachometer, tempertature, battery voltage, hour meter, oil pressure and ignition switch.

23.Document Box – Contains all documentation relating to the pump or engine.

24.Vacuum Pump Mechanical Seal Oil Reservoir – Oil level should always be maintained to the FULL level marked on the bottle.

25.Backflush Valve – Open valve to backflush wellpoints or to clean suction strainer.

26.Priming Tank Lifting Bail – When removing of the priming tank is required, attach a strap or chain of adequate lifting capacity to lift vacuum pump.

27.Pump Discharge – Attach discharge hose to this port. ALWAYS make sure discharge hose is securely attached.

28.Float Valve – Regulates and controls vacuum level during pump operation. Consist of self-aligning reinforced rubber hinge that doubles as a seal and a one piece welded float assembly.

29.PrimingTank – Vacuum system that creates a vacuum in the outer priming tank, drawing water in. Water drawn into the outer priming tank then flows into the volute, priming the pump.

30.Vacuum Gauge – Vacuum gauge for priming system. Monitors air discharge. Required when troubleshooting.

31.Fuel Tank – Holds 140 gallons (530 liters) of diesel fuel

32.Volute Inspection Cover – Remove this cover to inspect or clear the impeller.

33.Vacuum Pump – This unit uses a direct-drive 60 CFM vacuum pump to remove large volumes of air to obtain priming for the pump.

DRY PRIME PUMP — OPERATION AND PARTS MANUAL — REV. #3 (10/06/08) — PAGE 19

Page 18 Page 20
Page 19
Image 19
Multiquip MP150SDLTS, MP200DLTE, MP150SDLTE, MP200SDLSM, MP200DLSM, MP200DLTS, MP150SDLSM, P200DLST, MP200SDLTE Pump Components
Page 18 Page 20

MP200SDLTE, P200DLST, MP150SDLSM, MP200DLTS, MP200DLSM specifications

The Multiquip MP series of vibratory plate compactors, including models MP200DLTS, MP200DLTE, MP150SDLTE, P200DLST, and MP200SDLTE, are engineered for exceptional performance in compaction tasks across a variety of applications. These models are vital for contractors seeking efficiency, power, and reliability in the field.

The MP200DLTS and MP200DLTE models are particularly noteworthy for their robust design and versatility. Both are equipped with a powerful engine that delivers high centrifugal force, allowing operators to achieve effective compaction on different soil types. Their durable construction ensures longevity, even in demanding environments. The MP200DLTS features a dual-direction capability for increased maneuverability, while the MP200DLTE is designed for heavier-duty tasks and larger areas.

For users looking for a slightly more compact solution, the MP150SDLTE is a standout choice. This model combines portability with power, making it ideal for smaller jobs or confined spaces. It excels in providing precise compaction where larger equipment may struggle, while still maintaining high performance standards.

The P200DLST model offers enhanced features such as a heavy-duty baseplate designed to offer increased stability and excellent surface contact. This contributes to better results when compacting asphalt or granular materials, making it a preferred choice for road construction and repair projects.

Finally, the MP200SDLTE boasts advanced technology that enriches its operational capabilities. With an integrated vibration control system, users can adjust the compaction force on the fly, allowing for tailored performance based on specific job requirements. Its ergonomic handle design enhances user comfort, reducing fatigue during extended use.

Safety is also a priority in these models, with features such as protective guards and emergency stop buttons, ensuring that operators can work confidently. The overall combination of power, versatility, and innovative features makes the Multiquip MP series an essential tool for contractors in both construction and landscaping sectors.

In summary, whether it’s the heavy-duty capabilities of the MP200 series or the compact efficiency of the MP150SDLTE, Multiquip's offerings deliver outstanding performance, making them ideal for various compaction tasks. The robust engineering and thoughtful features provide users with the reliability needed in today’s competitive marketplace.
Top Page Image Contents