PUMP COMPONENTS

Figure 4 shows the location of the components and basic components for the MQ62TDD trash pump, The function of each component or control is described below:

1.Lifting Bail – When lifting of the trash pump by crane is required, use this lifting bail. Note: this lifting bail is balanced for a fully configured trash pump; removal of any trash pump components will un-balance the lifting bail.

2.Pump Discharge Port – Discharges water and debris from the pump.

3.Muffler/Guard – DO NOT touch the muffler when engine is running. The muffler can become extremely hot, causing severe burns. NEVER run the pump with the muffler guard removed.

4.Oil Filler – Fill as recommended in the maintenance section of this manual.

5.Engine (Diesel) – This pump uses a Deutz F2L2011/ D2011L02 air-cooled, 4-stroke diesel engine. See the Deutz Operation manual supplied with the trash pump for additional engine information.

6.Control Box Panel – Monitors engine functions and will shut down the engine for low oil pressure, high coolant temperature, alternator charge and V-belt failure.

7.Battery – +12 VDC battery compartment.

8.Tow End Jack Stand – When connecting the pump to a ball type towing hitch, use this jack stand to raise and lower the pump.

9.Fuel Filler Port – When the adding of fuel is required, remove fuel cap and add fuel through this port. Re- fuel using only recommended types of diesel fuels (see Deutz Operation Manual). DO NOT top off fuel, wipe up any spilled fuel immediately.

10.Tow Hitch Coupler – Requires a 2-inch ball hitch.

11.Safety Chain – ALWAYS attach safety chain to the towing vehicle. NEVER! tow the trash pump with the safety chain unattached.

12.Documentation Box – Contains documentation for the pump and engine.

13.Fuel Cell – This pump can be configured to operate with either a 16, 23 or 41 gallon fuel cell.

14.Tie-Downs – When the pump is placed on a flatbed truck for transport, use these tie-down points (4) to secure the trailer frame to the flatbed.

15.Fuel Cell Drain Plug – Located underneath the fuel cell, remove this drain plug to drain the fuel tank.

16.Engine Throttle Lever – Controls the speed of the engine. For load conditions (pumping water) ALWAYS run the engine at full speed.

17.Dipstick – Read this gauge to determine the oil level in the engine crankcase. Fill with only recommended type oil as referenced in the maintenance section of this manual.

18.Fuel Filter – Replace or clean the fuel filter as specified in the maintenance section of this manual.

19.Chock Blocks – Place these blocks (not included as part of the trash pump package) under each trailer wheel to prevent rolling.

20.Fuel Gauge – Read this gauge to determin if the fuel level is low is low. If fuel level is low, replenish with only recommended type diesel fuel.

21.Clean-Out Cover – Remove this cover to clean and remove foreign debris from the trash pump.

22.Accessories – Hoses, strainers and clamps are the required accessory components for normal operation of this trash pump. Contact your nearest Multiquip dealer for information on the components.

23.Trailer Lights – Before towing trash pump, make sure that both trailer lights are functioning correctly. NEVER tow the trash pump if these lights are not working.

24.Pump Intake Port – Intakes water and debris from the source.

25.Fill Cap – Remove this cap to prime the pump with water.

MQ62TDD TRASH PUMP • OPERATION AND PARTS MANUAL — REV. #0 (07/30/09) — PAGE 19

Page 18 Page 20
Page 19
Image 19
Multiquip MQ62TDD manual Tow Hitch Coupler Requires a 2-inch ball hitch
Page 18 Page 20

MQ62TDD specifications

The Multiquip MQ62TDD is a robust engine-driven compressor designed to deliver exceptional performance and reliability in challenging job site conditions. This portable unit is engineered for a wide range of applications, including construction, HVAC, and industrial use. With its powerful engine and user-friendly features, the MQ62TDD stands out as an ideal choice for contractors needing dependable air supply on the go.

One of the primary features of the MQ62TDD is its impressive air output. The unit boasts a maximum air flow rate of up to 62 CFM, allowing it to power multiple pneumatic tools simultaneously. Whether you are operating jackhammers, nail guns, or air impact wrenches, the MQ62TDD ensures consistent and sufficient air pressure to keep your projects moving efficiently.

The MQ62TDD is equipped with a 9-horsepower Honda engine, providing the necessary power to drive the compressor. Honda engines are renowned for their durability and fuel efficiency, and this model is no exception. With an extended run time due to its large fuel tank, the MQ62TDD minimizes downtime, which can be crucial in time-sensitive projects.

In terms of technological advancements, the MQ62TDD features an advanced cooling system designed to keep the compressor operating at optimal temperatures, thus extending the lifespan of the unit. The unit’s lightweight design, combined with a sturdy frame, makes transportation on site straightforward. The integrated handle and collapsible wheels facilitate easy maneuverability, ensuring that the compressor can be relocated without hassle.

Safety is also a priority with the Multiquip MQ62TDD. The unit is designed with protective features such as a low oil shutdown mechanism, which helps to prevent engine damage by automatically turning off if the oil level gets too low. Additionally, the compressor features sound-dampening technology that significantly reduces noise levels, making it ideal for use in noise-sensitive environments.

Overall, the Multiquip MQ62TDD compressor is a versatile, durable, and user-friendly tool that meets the demands of professional contractors. With its high air output, reliable power source, advanced technologies, and safety features, it provides the efficiency and performance needed to tackle any job with confidence.
Top Page Image Contents