TIRE SAFETY

TIRE SAFETY

Unsafe Tires, Lug Nuts or Wheels

Trailer tires and wheels are more likely to fail than car tires and wheels because they carry a heavier load. Therefore, it is essential to inspect the trailer tires before each tow.

If a tire has a bald spot, bulge, cuts, is showing any cords, or is cracked, replace the tire before towing. If a tire has uneven tread wear, take the trailer to a dealer service center for diagnosis.

Uneven tread wear can be caused by tire imbalance, axle misalignment or incorrect inflation.

Tires with too little tread will not provide adequate tracking on wet roadways and can result in loss of control, leading to death or serious injury.

Improper tire pressure causes an unstable trailer and can result in a tire blowout and loss of control. Therefore, before each tow you must also check the tire pressure. Tire pressure must be checked when tires are cold.

Allow 3 hours cool-down after driving as much as 1 mile at 40 m.p.h. before checking tire pressure. NOTE:Trailer tires willbe inflated to higher pressures than passenger vehicle tires.

Since trailer wheels and lug nuts (or bolts) are subjected to greater side loads than automobile wheels, they are more prone to loosen. Before each tow, check to make sure they are tight.

The proper tightness (torque) for lug nuts is listed in the lug nut tightening section of this manual. Use a torque wrench to tighten the lug nuts. If you do not have a torque wrench, use a lug wrench (from your tow vehicle) and tighten the nuts as much as you can. Then have a service garage or trailer dealer tighten the lug nuts to the proper torque.

WARNING — Lug Nut Tightening

Metal creep between the wheel rim and lug nuts will cause rim to loosen and could result in a wheel coming off, leading to death or serious injury.

Tighten lug nuts before each tow.

Lug nuts are also prone to loosen after first being assembled. When driving a new trailer (or after wheels

havebeen remounted), check to make sure they are tight after the first 10, 25 and 50 miles of driving and before each tow thereafter.

Failure to perform this check can result in a wheel parting from the trailer and a crash, leading to death or serious injury.

WARNING — Lug Nut Loosening

Lug nuts are prone to loosen after initial installation, which can lead to death or serious injury.

Check lug nuts for tightness on a new trailer or when wheel(s) have been remounted after the first 10, 25 and 50 miles of driving.

WARNING — Improper Lug Nut Torque

Improper lug nut torque can cause a wheel parting from the trailer, leading to death or serious injury.

Be sure lug nuts are tight before each tow.

WARNING — Tire Pressure

Improper tire pressure can result in a blowout and loss of control, which can lead to death or serious injury.

Be sure tires are inflated to pressure indicated on side wall before towing trailer.

MQ62TDD TRASH PUMP • OPERATION AND PARTS MANUAL — REV. #0 (07/30/09) — PAGE 41

Page 40 Page 42
Page 41
Image 41
Multiquip MQ62TDD manual Tire Safety, Unsafe Tires, Lug Nuts or Wheels, Tighten lug nuts before each tow
Page 40 Page 42

MQ62TDD specifications

The Multiquip MQ62TDD is a robust engine-driven compressor designed to deliver exceptional performance and reliability in challenging job site conditions. This portable unit is engineered for a wide range of applications, including construction, HVAC, and industrial use. With its powerful engine and user-friendly features, the MQ62TDD stands out as an ideal choice for contractors needing dependable air supply on the go.

One of the primary features of the MQ62TDD is its impressive air output. The unit boasts a maximum air flow rate of up to 62 CFM, allowing it to power multiple pneumatic tools simultaneously. Whether you are operating jackhammers, nail guns, or air impact wrenches, the MQ62TDD ensures consistent and sufficient air pressure to keep your projects moving efficiently.

The MQ62TDD is equipped with a 9-horsepower Honda engine, providing the necessary power to drive the compressor. Honda engines are renowned for their durability and fuel efficiency, and this model is no exception. With an extended run time due to its large fuel tank, the MQ62TDD minimizes downtime, which can be crucial in time-sensitive projects.

In terms of technological advancements, the MQ62TDD features an advanced cooling system designed to keep the compressor operating at optimal temperatures, thus extending the lifespan of the unit. The unit’s lightweight design, combined with a sturdy frame, makes transportation on site straightforward. The integrated handle and collapsible wheels facilitate easy maneuverability, ensuring that the compressor can be relocated without hassle.

Safety is also a priority with the Multiquip MQ62TDD. The unit is designed with protective features such as a low oil shutdown mechanism, which helps to prevent engine damage by automatically turning off if the oil level gets too low. Additionally, the compressor features sound-dampening technology that significantly reduces noise levels, making it ideal for use in noise-sensitive environments.

Overall, the Multiquip MQ62TDD compressor is a versatile, durable, and user-friendly tool that meets the demands of professional contractors. With its high air output, reliable power source, advanced technologies, and safety features, it provides the efficiency and performance needed to tackle any job with confidence.
Top Page Image Contents