|
| C | TM |
|
|
| |
| SUPER USER MENU |
| |
| RESET FAULT HISTORY | ▼ | |
| RESET EVENT HISTORY |
| |
| P1 PU/PD |
| |
| P1 TERMINATION |
| |
| P2 PU/PD |
| |
| ___________________________________ | ||
| HISTORY CLEARED | NO ▼ | |
| ___________________________________ | ||
| ▼▲ |
| |
| ▼ ▼ | MORE MENUS |
|
|
|
| |
|
| Super User Menu Screen 2 | |
|
| C | TM |
|
|
| |
| SUPER USER MENU |
| |
| COM 1 CONFIG DOWNLOAD | ▼ | |
| COM 2 CONFIG DOWNLOAD |
| |
| USB CONFIG DOWNLOAD |
| |
| FACTORY AUTO TEST |
| |
| FIRMWARE DOWNLOAD |
| |
| ___________________________________ | ||
| 28% |
| YES▼ |
| ___________________________________ | ||
| ▼▲ |
| |
| ▼ ▼ |
|
|
|
|
|
|
Super User Menu Screen 3
6.3.17 Configuration Download (Download Only Screen)
C
TM
CONFIRATION DOWNLOAD
COM 1 | CONFIG DOWNLOAD | ▼ |
COM 2 | CONFIG DOWNLOAD |
|
USB CONFIG DOWNLOAD |
| |
FIRMWARE DOWNLOAD |
| |
___________________________________
NO ▼
___________________________________
▼▲
Download Only Screen
Also, the message “History Cleared” will be displayed until another key is pressed.
d)Reset Fault History
e)Reset Event History
The P1 and P2 signify Communication Port 1 and Communication Port 2 and are for setting up the RS485 inter- faces on the display’s serial ports. PU/PD designates the
f)P1 PU/PD
g)P2 Termination
h)P2 PU/PD
i)P2 Termination
New configurations can be downloaded to the display by selecting the desired connection here. After enabling the download, download progress is indicated on the left side of the edit box as a percentage complete. After selecting Yes for download, and until No is selected after download is com- plete, only the Enter key will be active. See Section 6.2 for fur- ther details about downloading configurations.
j)Com 1 Config Download
k)Com2 Config Download
l)USB Config Download
m)Factory Auto Test: For factory use ONLY.
n)Firmware Download: A firmware update mode screen will remain until the unit has been reset by remote command or a power cycle. See Section 7.2.5 for downloading new firmware.
This menu allows for download only and can be accessed through the Special Jump Code 35. It is the only screen available by entering the password 35.
a)Com 1 Config Download: Selecting Yes initiates configu- ration download through Communication Port 1.
b)Com2 Config Download: Selecting Yes initiates configu- ration download through Communication Port 2.
c)USB Config Download: Selecting Yes initiates configura- tion download through USB port.
d)Firmware Download: Selecting Yes Initiates the download.
6.3.18 Display Board Status |
|
| ||
|
| C | TM |
|
|
|
|
| |
| MVIEW BOARD STATUS |
|
| |
| BATTERY VOLTS |
| ▼ | |
| BOARD CURRENT |
|
| |
| TEMPERATURE |
|
| |
| HEATER PWM % |
|
| |
| RESET SOURCE |
|
| |
| ___________________________________ | |||
|
|
| 23.3 VDC | ▼ |
| ___________________________________ | |||
| ▼▼ | MORE MENUS |
|
|
|
| MView Board Status Screen | ||
The user may view diagnostic information that reflects the operating conditions of the
a)Battery Volts
b)Board Current
c)Temperature
d)Heater PWM %
e)Reset Source
