Manuals / NEC / Computer Equipment / Computer Monitor

NEC RS-232C manual

Models: RS-232C

1 72

Download 72 pages 50.57 Kb

00h No Error Commands Power control procedure RS-232C Remote control Power control

Page 65

ETX (03h): End of Message

Check code

BCC: Block Check Code

Refer to the section 4.5 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

(65/72)

Page 64 Page 66

Image 65

NEC RS-232C manual

Page 64 Page 66

Related manuals

Manual 50 pages 13.24 Kb

Related pages Troubleshooting Guides for Frymaster CFD Out Outbound specification of the frame output side for Hitachi GR2000 Series 200-299, Memory Test Error Codes for Compaq ML370 Motors Voltage Diagram Volt Single Phase for Grizzly G9740 Where can I buy a USB hub for my Philips monitor? for Philips 201P Guida all’installazione for Sonos ZP80 Parts LiST and Schematic for Motor for Craftsman 137218030001 Remote Control Operation/Code List for Panasonic TH 50PZ700U Using Calculator’s Menu for Panasonic KX-UT670 AP-15U, AP-15TU, AP-15TUC Installation Instructions for Atlas Sound AP-15U What is the warranty on Dimplex replacement parts?

Contents

External Control 10.1 Application LAN control II. Preparation Connectors and wiringRS-232C Remote control Ascii Communication timing Get Parameter Reply Monitor Communication Format ALL Header block format fixed lengthPage STX Message block formatETX MSB LSB 10/72 SOH Check code Delimiter Get current Parameter from a monitor Message type Get parameter reply 00h No Error ETX MSB LSB Set parameter Current condition Set parameter reply Save Current Settings Commands Get Timing Report and Timing reply  Send 0730h, 37h as Get Timing Report command Null Message BCC IV. Control Commands Typical procedure exampleHow to change the Backlight setting Message Check code Delimiter Header Message Check code Delimiter SOH-0-Monitor ID-0-E-0-A STX-0-2-7-8-0-0-0-1-ETX SOH-0-Monitor ID-0-C-0-6 STX-0-2-7-9-ETX Readout value is 2s complement Dicom SIM Operation Code OP code Table Position 00h 20h Left side OP code Parameter Remarks Cod Pag Input Resolution DAh Hdmi Surround PIP RGB/HV OSD 02h 7Dh None DVI-HD DVI-PCScart IP ON/PROGRESSIVE Screen Mute on Screen Mute OFF MTS Mute Unmute Screen Mute‘SURROUND’ PIP ON/OFF OP code Parameter Remarks Cod Pag PIP Input 02h 73h No mean Power status read Power control procedure CR 0Dh End of packet 37/72 Controller requests the monitor to control monitor power Power control Delimiter CR 0Dh End of packet 39/72 Asset Data Read Request and reply Asset Data read and write Delimiter CR 0Dh End of packet 41/72 Asset Data write CR 0Dh End of packet 43/72 BCC DS-ETX Date & Time read and writeDate & Time Read MN Minutes 0-030h, 30h Date & Time Write Check code Delimiter Delimiter CR 0Dh End of packet 48/72 Schedule Read Schedule read and write B33h, 42h C33h, 43h On timer isnt set Page BCC OFF HOUR-OFF MIN-INPUT-WD-FL-ETX B33h, 42h 59 =3Bh C33h, 43h Off timer isn’t set Schedule Write PG-ON HOURS-ON MIN-OFF HOURS-OFF MIN-INPUT-WD-FL-P ModePage BCC OFF HOUR-OFF MIN-INPUT-WD-FL-P Mode 57/72 SOH-0-Monitor ID-0-A-0-A STX-C-2-1-5-PG-EN-ETX Delimiter CR 0Dh End of packet 59/72 STX-C-2-1-4-PG-ON HOUR-ON MIN SOH-0-0-Monitor ID-B-1-8 STX-C-3-1-4-ST-PG-ON HOUR-ON MIN 030h, 30h 731h, 37h 23 =17h 831h, 38h Off timer isnt set SOH-0-0-Monitor ID-B-0-C STX-C-3-1-5-ST-PG-EN-ETX Self-diagnosis status read Self diagnosisPage Serial No. Read Serial No. & Model Name Read Model Name Read Security Lock Control Security Lock STX-C-3-1-D-ST-EN-ETX Direct TV Chanel Read & Reply Direct TV Chanel Read & Write Direct TV Chanel Write & Reply All data are subject to change without notice

Top Page Image Contents