Delimiter
CR (0Dh): End of packet
2) The monitor replies a data for confirmation.
Header | Message | | Check code | Delimiter |
SOH-'0'-'0'-Monitor ID-'B'-'2'-'8' | STX-'C'-'3'-'2'-'2'-ST-PG-ON HOUR-ON MIN- | | BCC | CR |
| OFF HOUR-OFF MIN-INPUT-WD-FL-P MODE- | | | |
| EXT1-EXT2-EXT3-EXT4-EXT5-EXT6-EXT7-ETX | | | |
Header | | | | |
SOH (01h): Start Of Header | | |
'0' (30h): Reserved | | | | |
'0' (30h): Message receiver is the controller. | | |
Monitor ID: Indicate a replying Monitor ID. | | |
Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. | |
'B' (42h): Message type is "Command reply". | | |
'2'-'8'(32h, 38h): Message length | | |
Message | | | | |
STX (02h): Start of Message | | |
'C'-'3'-'2'-'2' (43h, 33h, 32h, 32h): Schedule writes reply command | | |
ST: Schedule Status command | | |
'0'-'0'(30h, 30h): No error | | |
'0'-'1'(30h, 31h): Error | | |
PG-ON HOURS-ON MIN-OFF HOURS-OFF MIN-INPUT-WD-FL-P MODE | | |
EXT1-EXT2-EXT3-EXT4-EXT5-EXT6-EXT7: Schedule data | | |
PG: Program No. | | | | |
'0'-'0'(30h, 30h): Program No.1 | | |
| | | | |
'0'-'6'(30h, 36h): Program No.7 | | |
ON_HOUR: Turn on time (hour) '0'-'0'(30h, 30h): 00
'1'-'7'(31h, 37h): 23 (=17h)
'1'-'8'(31h, 38h): ON timer isn't set.
ON_MIN: Turn on time (minute) '0'-'0'(30h, 30h): 0
'3'-'B'(33h, 42h): 59
'3'-'C'(33h, 43h): On timer isn’t set.
OFF_HOUR: Turn off time (hour) '0'-'0'(30h, 30h): 00
'1'-'7'(31h, 37h): 23 (=17h)
'1'-'8'(31h, 38h): Off timer isn't set.
OFF_MIN: Turn off time (minute) '0'-'0'(30h, 30h): 0
'3'-'B'(33h, 42h): 59 (=3Bh)
'3'-'C'(33h, 43h): Off timer isn’t set.
INPUT: Timer input
'0'-'0'(30h,30h): No mean (works on last memory)
'0'-'1'(30h,31h): VGA
'0'-'2'(30h,32h): RGB/HV
'0'-'3'(30h,33h): DVI
'0'-'5'(30h,35h): Video1
'0'-'6'(30h,36h): Video2
'0'-'7'(30h,37h): S-Video
'0'-'A'(30h,41h): TV
'0'-'C'(30h,43h): DVD/HD1
'0'-'D'(30h,44h): Option
'0'-'E'(30h,45h): DVD/HD2
'0'-'F'(30h,46h): Display Port
'1'-'1'(31h,31h): HDMI