Plan the Installation | Net Optics none instruction

Director

Plan the Installation

Before you begin the installation of your Director device, determine the following:

•Name that will identify the Director device

•IP address of the Director device, or a range of IP addresses if you are deploying multiple Director devices

•Net Mask for Director

•IP address of the remote management console, if deployed over a WAN; this address is used for SNMP traps

•Gateway to the remote management console, if deployed over a WAN

•Port assignments and filters for the Network and Monitor port connections

Make sure you have a suitable location to install the Director device. For power redundancy, use two independent power sources.

Unpack and Inspect the Director device

Carefully unpack the Director device, power supplies, and all cables that are provided. Director is delivered with the following:

•(1) Director device

•(2) Power cords

•Director Quick Install Guide (one sheet)

•(1) CD containing the Director User Guide (this document)

•Network and monitor cables

•RS-232 DB9 cable for use with the CLI

•Extended Warranty if purchased

Check the packing slip against parts received. If any component is missing or damaged, contact Net Optics Customer Service immediately at +1 (408) 737-7777. (Note: XFP modules are ordered and shipped separately.)

12

*** Confidential - DO NOT Distribute ***

Image 16

Net Optics none manual Plan the Installation, Unpack and Inspect the Director device

Contents

Smart Filtering Appliance Trademarks and Copyrights Contents Appendix a Appendix BAppendix C Filter parameters Chapter Introduction Key Features Ease of UseMonitor port Filtering Passive, Secure Technology About this Guide Description Director Architecture Director internal architecture USB port Director Management Typical Application Network Links Monitoring Tools In-line Monitoring of 10 Gigabit Links IBypass Switch MethodExternal Network Tap method Power LEDs Director Front PanelMonitor Port LEDs DNM / Network Port LEDs Director Rear Panel XFP Chapter Installing Director Plan the Installation Unpack and Inspect the Director device Install SFP and XFP Monitor port Modules Install Director Network ModulesRack Mount the Director device Connect Power to Director Connect the local CLI Interface Connect the remote CLI Interface Baud Data bits No parity 1 stop bit No flow controlTip To connect the CLI for remote use over the Management port Log into the CLI To log into the CLI Change Director User Name and Password Configure Director using the CLITo change the user name and password To change the port mode Assign a New Manager IP AddressTo assign a new Manager IP address to Director Change Port Modes Save and Load Director Configurations Set the Current Date and Time Using the CLI Help Command To view CLI help information Using the CLI Command History Buffer Current config file Connect Span Ports to Director To connect a Span port Connect Director With In-line Network Links To connect an in-line network link Check the Installation Configure a Matrix Switch connection in DirectorConnect Monitoring Tools to Director Chapter Configuring Filters Using the CLI Syntax Enter filter commit. The switch connection is activated Copy Traffic From Any Network Port to Any Monitor Port Regenerate Traffic to Any Set of Monitor Ports Lter add inports=n1.1 action=redir redirports=m.3-m.5 Create Filters To create a filter that selects IPv4 packets by protocol Create Complex Filters Logical and filter connection View filters UDP Work with configurable 10 Gigabit ports Configurable 10 Gigabit XFP ports used as Network ports Network Port 11 XFP Port Understand filter interactions CAM Flow diagram now looks as follows Exclusive filters N1.1 ipproto=UDP action=drop N1.1 m.1 To change the Director filter configuration Understand pending and active filters Enter filter list to view the pending filter list User interactions Filter capacity Daisy-chaining Multiple Director Chassis Appendix a Director Specifications Specifications, chassis Specifications, DNM EnvironmentalCertifications Available Models Appendix B Command Line Interface Command Sub-Command Parameters Example and description Command may include Filter add and filter ins commandsFilter add ipv6=n inports=n1.1-n1.3 ip Src=10.1.1.1 action=drop Load myconfiguration-1 Filter listFilter running Filter sync Save myconfiguration-1 Show myconfiguration-1Passwd Ping Sysip commit Sysip ipaddr=192.168.1.2 netmask=255.255.0.0Sysip show Time This This command is only available at root level Command User showUser add name=bob pw=bob-pw priv=3 Is only Filter parameters Director Filter Parameters Qual Value Example Description Appendix C Protocol Numbers Num Keyword Protocol Mobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved