Appendix C Protocol Numbers, Num Keyword Protocol | Net Optics none

Director

Appendix C

Protocol Numbers

The official Assigned Internet Protocol Numbers list is maintained by the Internet Assigned Numbers Authority and can be found at http://www.iana.org/assignments/protocol-numbers. The list as of April 18, 2008 is reproduced in the following table (without references).

Num	Keyword	Protocol

0	HOPOPT	IPv6 Hop-by-Hop Option

1	ICMP	Internet Control Message

2	IGMP	Internet Group Management

3	GGP	Gateway-to-Gateway

4	IP	IP in IP (encapsulation)

5	ST	Stream

6	TCP	Transmission Control

7	CBT	CBT

8	EGP	Exterior Gateway Protocol

9	IGP	any private interior gateway
		(used by Cisco for their
		IGRP)

10	BBN-	BBN RCC Monitoring
	RCC-
	MON

11	NVP-II	Network Voice Protocol

12	PUP	PUP

13	ARGUS	ARGUS

14	EMCON	EMCON

15	XNET	Cross Net Debugger

16	CHAOS	Chaos

17	UDP	User Datagram

18	MUX	Multiplexing

19	DCN-	DCN Measurement Subsys-
	MEAS	tems

20	HMP	Host Monitoring

21	PRM	Packet Radio Measurement

22	XNS-IDP	XEROX NS IDP

23	TRUNK-1	Trunk-1

24	TRUNK-2	Trunk-2

25	LEAF-1	Leaf-1

26	LEAF-2	Leaf-2

27	RDP	Reliable Data Protocol

28	IRTP	Internet Reliable Transaction

29	ISO-TP4	ISO Transport Protocol Class
		4

Num	Keyword	Protocol

30	NETBLT	Bulk Data Transfer Protocol

31	MFE-NSP	MFE Network Services
		Protocol

32	MERIT-	MERIT Internodal Protocol
	INP

33	DCCP	Datagram Congestion Control
		Protocol

34	3PC	Third Party Connect Protocol

35	IDPR	Inter-Domain Policy Routing
		Protocol

36	XTP	XTP

37	DDP	Datagram Delivery Protocol

38	IDPR-	IDPR Control Message
	CMTP	Transport Proto

39	TP++	TP++ Transport Protocol

40	IL	IL Transport Protocol

41	IPv6	Ipv6

42	SDRP	Source Demand Routing
		Protocol

43	IPv6-	Routing Header for IPv6
	Route

44	IPv6-Frag	Fragment Header for IPv6

45	IDRP	Inter-Domain Routing Pro-
		tocol

46	RSVP	Reservation Protocol

47	GRE	General Routing Encapsula-
		tion

48	DSR	Dynamic Source Routing
		Protocol

49	BNA	BNA

50	ESP	Encap Security Payload

51	AH	Authentication Header

52	I-NLSP	Integrated Net Layer Security
		TUBA

53	SWIPE	IP with Encryption

54	NARP	NBMA Address Resolution
		Protocol

49

*** Confidential - DO NOT Distribute ***

Image 53

Net Optics none manual Appendix C Protocol Numbers, Num Keyword Protocol

Contents

Smart Filtering Appliance Trademarks and Copyrights Contents Appendix B Appendix aAppendix C Filter parameters Chapter Introduction Ease of Use Key FeaturesMonitor port Filtering Passive, Secure Technology Description About this Guide Director internal architecture Director Architecture Director Management USB port Network Links Typical Application Monitoring Tools External Network Tap method IBypass Switch MethodIn-line Monitoring of 10 Gigabit Links Director Front Panel Power LEDsMonitor Port LEDs DNM / Network Port LEDs XFP Director Rear Panel Chapter Installing Director Unpack and Inspect the Director device Plan the Installation Rack Mount the Director device Install Director Network ModulesInstall SFP and XFP Monitor port Modules Connect the local CLI Interface Connect Power to Director Baud Data bits No parity 1 stop bit No flow control Connect the remote CLI InterfaceTip To connect the CLI for remote use over the Management port To log into the CLI Log into the CLI To change the user name and password Configure Director using the CLIChange Director User Name and Password Assign a New Manager IP Address To change the port modeTo assign a new Manager IP address to Director Change Port Modes Set the Current Date and Time Save and Load Director Configurations To view CLI help information Using the CLI Help Command Current config file Using the CLI Command History Buffer To connect a Span port Connect Span Ports to Director To connect an in-line network link Connect Director With In-line Network Links Connect Monitoring Tools to Director Configure a Matrix Switch connection in DirectorCheck the Installation Syntax Chapter Configuring Filters Using the CLI Copy Traffic From Any Network Port to Any Monitor Port Enter filter commit. The switch connection is activated Lter add inports=n1.1 action=redir redirports=m.3-m.5 Regenerate Traffic to Any Set of Monitor Ports To create a filter that selects IPv4 packets by protocol Create Filters Logical and filter connection Create Complex Filters UDP View filters Configurable 10 Gigabit XFP ports used as Network ports Work with configurable 10 Gigabit ports Network Port 11 XFP Port CAM Understand filter interactions Flow diagram now looks as follows N1.1 ipproto=UDP action=drop N1.1 m.1 Exclusive filters Understand pending and active filters To change the Director filter configuration Enter filter list to view the pending filter list Filter capacity User interactions Daisy-chaining Multiple Director Chassis Specifications, chassis Appendix a Director Specifications Environmental Specifications, DNMCertifications Available Models Command Sub-Command Parameters Example and description Appendix B Command Line Interface Filter add and filter ins commands Command may includeFilter add ipv6=n inports=n1.1-n1.3 ip Src=10.1.1.1 action=drop Filter list Load myconfiguration-1Filter running Filter sync Show myconfiguration-1 Save myconfiguration-1Passwd Ping Sysip ipaddr=192.168.1.2 netmask=255.255.0.0 Sysip commitSysip show Time User show This This command is only available at root level CommandUser add name=bob pw=bob-pw priv=3 Is only Director Filter Parameters Qual Value Example Description Filter parameters Num Keyword Protocol Appendix C Protocol Numbers Mobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved