Sysip commit, Sysip show, Time | Net Optics none manual


					Director


Command		Sub-Command	Parameters	Example and description

sysip		commit		sysip commit
				Activates pending changes defined with sysip set

		set	ipaddr=<address>	sysip ipaddr=192.168.1.2 netmask=255.255.0.0>
			netmask=<netmask>	Parameters:
			gw=<gateway>	<address> is the IP address (default: 192.168.1.2)
				<netmask> is the netmask (default: 255.0.0.0)
				<gateway> is the gateway IP address (default:
				192.168.1.1)
				Sets the Director IP address, netmask, and gateway
				IP address; requires a sysip commit command to
				activate the new settings

		show		sysip show
				Displays the current Director IP address information

time			<time>	time 13:02:00
				Parameters:
				<time> is hh:mm:ss
				Sets the system time-of-day; if <time> is omitted, the
				current time is displayed

upgrade			srvip=<svrip>	upgrade srvip=168.192.20.2 user=bob pw=bobpw
			user=<username>	filename=image021108 2
			pw=<passwd>	Parameter:
			filename=<filename>	<svrip> is the IP address of the server that the
				new image file is on
				<username> is the user name needed for FTP
				access to the server
				<passwd> is the password needed for FTP
				access to the server
				<filename> is the name of the image file
				Replaces the current system boot image with the
				image in the specified file (see image command); all
				parameters must be included and they must be in the
				order shown

46

*** Confidential - DO NOT Distribute ***

Image 50

Net Optics none manual Sysip commit, Sysip ipaddr=192.168.1.2 netmask=255.255.0.0, Sysip show, Time, Filename=image021108

Contents

Smart Filtering Appliance Trademarks and Copyrights Contents Appendix C Appendix aAppendix B Filter parameters Chapter Introduction Monitor port Filtering Key FeaturesEase of Use Passive, Secure Technology About this Guide Description Director Architecture Director internal architecture USB port Director Management Typical Application Network Links Monitoring Tools External Network Tap method IBypass Switch MethodIn-line Monitoring of 10 Gigabit Links Monitor Port LEDs Power LEDsDirector Front Panel DNM / Network Port LEDs Director Rear Panel XFP Chapter Installing Director Plan the Installation Unpack and Inspect the Director device Rack Mount the Director device Install Director Network ModulesInstall SFP and XFP Monitor port Modules Connect Power to Director Connect the local CLI Interface Tip Connect the remote CLI InterfaceBaud Data bits No parity 1 stop bit No flow control To connect the CLI for remote use over the Management port Log into the CLI To log into the CLI To change the user name and password Configure Director using the CLIChange Director User Name and Password To assign a new Manager IP address to Director To change the port modeAssign a New Manager IP Address Change Port Modes Save and Load Director Configurations Set the Current Date and Time Using the CLI Help Command To view CLI help information Using the CLI Command History Buffer Current config file Connect Span Ports to Director To connect a Span port Connect Director With In-line Network Links To connect an in-line network link Connect Monitoring Tools to Director Configure a Matrix Switch connection in DirectorCheck the Installation Chapter Configuring Filters Using the CLI Syntax Enter filter commit. The switch connection is activated Copy Traffic From Any Network Port to Any Monitor Port Regenerate Traffic to Any Set of Monitor Ports Lter add inports=n1.1 action=redir redirports=m.3-m.5 Create Filters To create a filter that selects IPv4 packets by protocol Create Complex Filters Logical and filter connection View filters UDP Work with configurable 10 Gigabit ports Configurable 10 Gigabit XFP ports used as Network ports Network Port 11 XFP Port Understand filter interactions CAM Flow diagram now looks as follows Exclusive filters N1.1 ipproto=UDP action=drop N1.1 m.1 To change the Director filter configuration Understand pending and active filters Enter filter list to view the pending filter list User interactions Filter capacity Daisy-chaining Multiple Director Chassis Appendix a Director Specifications Specifications, chassis Certifications Specifications, DNMEnvironmental Available Models Appendix B Command Line Interface Command Sub-Command Parameters Example and description Filter add ipv6=n inports=n1.1-n1.3 ip Command may includeFilter add and filter ins commands Src=10.1.1.1 action=drop Filter running Load myconfiguration-1Filter list Filter sync Passwd Save myconfiguration-1Show myconfiguration-1 Ping Sysip show Sysip commitSysip ipaddr=192.168.1.2 netmask=255.255.0.0 Time User add name=bob pw=bob-pw priv=3 This This command is only available at root level CommandUser show Is only Filter parameters Director Filter Parameters Qual Value Example Description Appendix C Protocol Numbers Num Keyword Protocol Mobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved