About this Guide, Description | Net Optics none specification

Director

About this Guide

Please read this entire guide before installing Director. This guide applies to the following part numbers:

Chassis Part Number	Description

DIR-3400	Director Main Chassis with 10 SFP monitor ports
DIR-____	Director Main Chassis with 10 SFP monitor ports, -48VDC power
DIR-7400	Director Main Chassis with 10 SFP monitor ports, 2 XFP 10GbE ports, 2 XFP uplink ports
DIR-____	Director Main Chassis with 10 SFP monitor ports, 2 XFP 10GbE ports, 2 XFP uplink ports,
	-48VDC power
DNM Part Number	Description

DNM-100	6-Port 10/100/1000 Copper In-Line Module
DNM-110	12-Port 10/100/1000 Copper Span Module
DNM-200	6-Port Gigabit SX Fiber 62.5μm In-Line Module
DNM-210	12-Port Gigabit SX Fiber 62.5μm Span Module
DNM-220	6-Port Gigabit SX Fiber 50μm In-Line Module
DNM-230	12-Port Gigabit SX Fiber 50μm Span Module
DNM-300	6-Port Gigabit LX Fiber In-Line Module
DNM-310	12-Port Gigabit LX Fiber Span Module
DNM-320	6-Port Gigabit ZX Fiber In-Line Module
DNM-330	12-Port Gigabit ZX Fiber Span Module

3

*** Confidential - DO NOT Distribute ***

Image 7

Net Optics none manual About this Guide, Description

Contents

Smart Filtering Appliance Trademarks and Copyrights Contents Filter parameters Appendix aAppendix B Appendix C Chapter Introduction Passive, Secure Technology Key FeaturesEase of Use Monitor port Filtering Description About this Guide Director internal architecture Director Architecture Director Management USB port Network Links Typical Application Monitoring Tools In-line Monitoring of 10 Gigabit Links IBypass Switch MethodExternal Network Tap method DNM / Network Port LEDs Power LEDsDirector Front Panel Monitor Port LEDs XFP Director Rear Panel Chapter Installing Director Unpack and Inspect the Director device Plan the Installation Install SFP and XFP Monitor port Modules Install Director Network ModulesRack Mount the Director device Connect the local CLI Interface Connect Power to Director To connect the CLI for remote use over the Management port Connect the remote CLI InterfaceBaud Data bits No parity 1 stop bit No flow control Tip To log into the CLI Log into the CLI Change Director User Name and Password Configure Director using the CLITo change the user name and password Change Port Modes To change the port modeAssign a New Manager IP Address To assign a new Manager IP address to Director Set the Current Date and Time Save and Load Director Configurations To view CLI help information Using the CLI Help Command Current config file Using the CLI Command History Buffer To connect a Span port Connect Span Ports to Director To connect an in-line network link Connect Director With In-line Network Links Check the Installation Configure a Matrix Switch connection in DirectorConnect Monitoring Tools to Director Syntax Chapter Configuring Filters Using the CLI Copy Traffic From Any Network Port to Any Monitor Port Enter filter commit. The switch connection is activated Lter add inports=n1.1 action=redir redirports=m.3-m.5 Regenerate Traffic to Any Set of Monitor Ports To create a filter that selects IPv4 packets by protocol Create Filters Logical and filter connection Create Complex Filters UDP View filters Configurable 10 Gigabit XFP ports used as Network ports Work with configurable 10 Gigabit ports Network Port 11 XFP Port CAM Understand filter interactions Flow diagram now looks as follows N1.1 ipproto=UDP action=drop N1.1 m.1 Exclusive filters Understand pending and active filters To change the Director filter configuration Enter filter list to view the pending filter list Filter capacity User interactions Daisy-chaining Multiple Director Chassis Specifications, chassis Appendix a Director Specifications Available Models Specifications, DNMEnvironmental Certifications Command Sub-Command Parameters Example and description Appendix B Command Line Interface Src=10.1.1.1 action=drop Command may includeFilter add and filter ins commands Filter add ipv6=n inports=n1.1-n1.3 ip Filter sync Load myconfiguration-1Filter list Filter running Ping Save myconfiguration-1Show myconfiguration-1 Passwd Time Sysip commitSysip ipaddr=192.168.1.2 netmask=255.255.0.0 Sysip show Is only This This command is only available at root level CommandUser show User add name=bob pw=bob-pw priv=3 Director Filter Parameters Qual Value Example Description Filter parameters Num Keyword Protocol Appendix C Protocol Numbers Mobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved