C o n t r o l p a n e l
•Allow plain text login — Select No, if you never want to send your password as plain text without encryption. Note that this option only affects PPP connections;
•Use PPP compression — Select Yes to speed up the data transfer, if it is supported by the remote PPP server. If you have problems establishing a connection, select No.
Setting up an Internet access point for a wireless LAN
Your device has a predefined Internet access point for a wireless LAN, but you can create new Internet access points yourself.
1.Select Connections > Internet setup.
2.Press New. You can use an existing Internet access point as a basis for the new one: after you have pressed New, press Yes. Select the access point from the list, and press OK.
3.Define the settings.
•Internet settings name — Enter a descriptive name for the Internet access point.
•Internet settings type — Select Wireless LAN as the connection type.
•Network ID — Select the network ID according to the destination network you want to access with the Internet access point. You can rename and create new network IDs. Using the correct network ID ensures that the data traffic is routed directly to the desired destination network. Especially VPN (virtual private network) software may restrict data traffic for a certain destination network. Network IDs can be used to filter Internet access points when establishing an Internet connection.
•Network mode — If you select the Infrastructure mode, devices can communicate with each other and with wired LAN devices through a wireless LAN access point. If you select the Ad hoc mode, devices can send and receive data directly with each other. No wireless LAN access point is needed.
•Network name — Type the network name (SSID - service set identifier) as defined by the system administrator, or press Change, and select one from the list. In the ad hoc mode, the users themselves name the wireless LAN. If you do not specify the network name here, you are asked to select a network when you establish a wireless LAN connection.
•Security mode — You must select the same security mode that is used in the wireless LAN access point. If you select WEP (wired equivalent privacy) or WPA
4.After defining the settings, press Advanced to define advanced settings, if necessary. Otherwise, press Finish or Done to exit the setup wizard.
Configuring advanced Internet access point settings
Press Advanced when you have finished setting up the basic Internet access point settings.
The pages and options available depend on the settings you have chosen. Ask your system administrator for the correct values.
IP configuration page
Note that the two protocols (IPv4 and IPv6) require slightly different settings.
•Auto retrieve IP — If you select Yes, the IP address is obtained automatically from the server. This setting is sometimes also called dynamic IP address. If you select No, you must specify the IP address, subnet mask, and default gateway in the fields below.
•Auto retrieve DNS — If you select Yes for the IPv4 protocol, or DHCP for the IPv6 protocol, the primary and secondary DNS (domain name server) addresses are obtained automatically from the server. DNS is an Internet service that translates domain names such as www.nokia.com into IPv4 addresses such as 192.100.124.195, or IPv6 addresses like 3ffe:2650:a640:1c2:341:c39:14. If you select No for the IPv4 protocol, or Manual for the IPv6 protocol, you must specify the IP addresses for the primary and secondary DNS servers.
Proxies page
You may want to use a proxy to quicken access to the Internet. Note also that some Internet service providers require the use of Web proxies. Contact your Internet service provider to determine proxy details.
If you have made an Internet connection to your company’s intranet, and are unable to retrieve Web pages from the general Internet, you may need to setup a proxy server to retrieve Web pages outside your company’s intranet.
Define the following:
•Proxy protocol — Select the protocol type of the proxy. You can set different proxy settings for each protocol.
•Use proxy server — Select Yes to use the proxy server.
•Proxy server — Enter the IP address of the proxy server, or the domain name. Example domain names are: company.com and organisation.org.
•Port number — The number of the proxy port. The port number is related to the protocol. Common values are 8000 and 8080, but vary with every proxy server.
•No proxy for — Define the domains for which the HTTP or HTTPS proxy is not needed.
Copyright © 2004 Nokia. All Rights Reserved. | 68 |
