Nokia CC100 Dconfig, Default, Diag, Dir, Dns, Exit, Quit, Ephpnareboot, Epstat, Epswc, Epswigmp

CC100Master Bridge User’s Guide

dconfig			Dump all configurations/settings.
default			Reset all settings to factory default, except Password.
		-t<mac>	On-line EP connection diagnosis.
diag		-r<mac>	-t: downstream SNR diagnosis(from Master to EP)
			-r: upstream SNR diagnosis(from EP to Master)
			<mac>: EP MAC <mac> to be diagnosed
			Show detail file information resides in flash ROM. Include
			‘Working Area’ and ‘Upload Area’, refer Figure 4. The listed
			filenames are,
			‘bootcode’: boot loader
			‘sysfw4m’: system firmware
dir			‘G1C28H21M’: Master HCNA driver
			‘G0C28H20Ep’: 3010 EP HCNA driver
			‘G1C28H21Ep’: 3110 EP HCNA driver
			‘diagsw’: 3010 diagnosis utility file
			‘diagsw1’: 3110 diagnosis utility file
			Accompanying with file id, file version, file date, and file size.
	[-s<pri/sec> <ip>]		Display or set up DNS server setting.
dns			-s pri <ip>: set up Primary DNS server’s IP
			-s sec <ip>: set up Secondary DNS server’s IP
exit			Close the Telnet console.
quit			Close the Telnet console.
	[-c<hostcnt>]		Set up the EP Properties Profile related setting values.
	[-n<note>]		<hostcnt>: EP Host Limit setting value (0~255), default 255
ep	[-u<uprate index>]		<note>: EP Note setting value
	<mac>		<uprate index>: EP Upstream Rate setting value ( 0~1563,
			*64Kbps), default 0 for unlimited
			<mac>: designated EP MAC to configure
ephpnareboot	-m<mac>		Reset remote Smart EP device
(Smart EP)
epstat	-m<mac>		Display remote Smart EP port statistics for port
		[-r]	LAN1/LAN2/HCNA.
(Smart EP)
			-r: reset all port statistics counter to 0
	-m<mac>		Display or set up remote Smart EP built-in switch Ethernet
	[-t]		properties
	[-u]		-t: display EP switch settings
	[-r]		-u: display EP switch/port status
	[-d]		-r: reset EP switch
	[-p<lan1/lan2/hpna>		-d: reset EP switch’s eeprom settings to factory default
epswc		[-l<up/down>]	-p: configure EP port LAN1/LAN2/HCNA
(Smart EP)		[-s<auto /10h /10f	-l: link, <up/down>: force current port to link up or down, i.e.
		/100h /100f>]	enable/disable current port
		[-f<on/off>]]	-s: current port Ethernet mode setting,
			<auto>: auto-negotiation mode
			<10h/10f/100h/100f>: 10/100Mbps, half/full-duplex mode
			-f: current port Ethernet flow-control setting,
			<on/off>: turn on /off flow control
epswigmp	-m<mac>		Refer swigmp, swqosq, swqosrate, swqostc, swtagvlan for the
epswqosq			same functionality, but operate on remote Smart EP with
epswqosrate			designated MAC address <mac>
epswqostc
epswtagvlan
(Smart EP)

filter

[-s<set>	Display or set up the filter rule set, refer the section “Allow
[-c<act/deact>]	Source” for IP <ip> and Subnet Mask setup <mask>.
[-a<ip> -m<mask>]	<set>: filter set index, total 16 set (0~15)
[-t<allow/deny>]	<act/deact>: activate or de-activate the rule set
[-w<allow/deny>]	<allow/deny>: allow or deny the protocol
	40