HOW TO SET UP THE INCLINE TRAINER
Assembly requires two persons. Set the INCLINE TRAINER in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Assembly can be completed using the included allen wrenches.
Note: The underside of the INCLINE TRAINER walking belt is coated with | |||||||||
shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This | |||||||||
is a normal condition and does not affect INCLINE TRAINER performance. If there is lubricant on top of the walk- | |||||||||
ing belt, simply wipe off the lubricant with a soft cloth and a mild, |
|
| |||||||
1. Slide the Right and Left Uprights (96, 107) onto the |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| 1 |
|
| 96 |
|
|
|
| |
brackets near the front of the Base Frame (52). Make |
|
|
|
|
| 107 |
| ||
|
|
|
|
| |||||
sure that the Uprights are on the correct sides; the |
|
|
|
| Holes |
|
|
| |
indicated holes must be facing the INCLINE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
TRAINER. |
|
|
|
|
|
|
|
|
|
Raise the Left Upright (107) until the lower hole in the |
|
|
|
|
front of the Left Upright is aligned with the upper hole in |
|
|
|
|
the bracket as shown. Thread an Upright Bolt (106) into |
|
|
|
|
the Left Upright and the bracket. Do not fully tighten | 106 | 52 |
|
|
the Upright Bolt yet. | 106 |
| ||
Repeat this step with the Right Upright (96). |
|
| 52 | |
2. While a second person holds the Handrail (94) near the | 2 |
| 89 |
|
Uprights (96, 107), feed the wires in both sides of the | 142 | 10 | ||
Handrail down into the Uprights. Pull the ends of the |
|
| ||
wires out of the lower ends of the Uprights and remove | 93 | 94 |
|
|
the wire ties from the ends of the wires. |
|
| ||
Finger tighten four Handrail Bolts (93) into the Handrail |
|
|
|
|
(94) and the Uprights (96, 107) as shown. Be careful to |
|
|
| 93 |
avoid pinching the wires in the Handrail. |
|
|
| |
Note: The Accessory Holder (142) and the Cup Holder | 96 |
| Wires |
|
(10) are replaceable. If these parts become dislodged |
| 107 | ||
from the Console (89), press them back into place. |
|
|
| |
3. Connect the Right Upright Wire Harness (105), the TV | 3 | 96 |
|
|
Cable (33), and the Left Upright Wire Harness (131) in |
| 107 | ||
the indicated locations. Push all of the excess wire up |
|
|
| |
into the Uprights (96, 107). Make sure that all wires are |
|
|
|
|
fully connected. Note: Regardless of which console |
|
|
|
|
your INCLINE TRAINER has, connect all wires so that |
|
|
|
|
the console can later be upgraded if desired. |
|
|
|
|
Refer to step 1. While a second person holds the Uprights (96, 107), remove the Upright Bolts (106). Slide the Uprights fully onto the Base Frame (52). Be careful to avoid pinching your hands or the wires.
105 | 33 | 131 |
|
7
