Manuals / Nortel Networks / Computer Equipment / Network Router

Nortel Networks 8600 manual Variable definitions

Models: 8600

1 136

Download 136 pages 14.91 Kb

Page 100

100Remote connection configuration using Device Manager

4Select the properties you want to change and configure their values.

5Click OK.

--End--

Variable definitions

Use the data in the following table to configure the Properties dialog box.

Variable	Value

Status Interval	Interval you use to gather statistics
	and status information (default is 20
	seconds).

(IfTraps, Status Interval)	The interval, in seconds, you use
	to gather statistics and status
	information. Configure this value if you
	select the Register for Traps box.

Hotswap Detect every	The number of intervals at which
	Device Manager checks for module
	hot swaps.

Enable	If you select this variable, Device
	Manager polls the switch according
	to the settings you select prior to the
	Enable box.

Retry Count	If Device Manager cannot transmit
	polling information at start up, the
	number of times Device Manager
	retransmits polling information.

Timeout	Length of the retry for each polling
	waiting period. If you access the
	device through a slow link, you can
	increase the timeout interval and
	change the retransmission strategy to
	superlinear.

Trace	If you select this variable, you can
	perform trace routes.

Register for Traps	If you select this variable, Device
	Manager registers a trap.

Listen for Traps	If you select this variable, Device
	Manager monitors for a trap.

Max Traps in Log	The specified number of traps that
	can exist in the trap log. The default is
	500.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319 01.01 Standard

30 May 2008

Copyright © 2008 Nortel Networks

Image 100

Nortel Networks 8600 manual Variable definitions

Contents

Commissioning Legal Notice Contents Initial steps using the Nncli Common procedures using Device Manager 127 Copyright 2008 Nortel Networks Software license Nortel Networks Inc. software license agreementGeneral Nortel Networks Inc. software license agreement Software license Features New in this releaseOther changes Document changesNew in this release Introduction NavigationIntroduction Commissioning fundamentals System connectionsTerminal connection Modem connectionPPP modem connection Data terminal Ready DTR Ground GND Data set readyRequest to send Clear to sendPPP configuration topology System logon Hsecure mode Default passwords and community stringsSetup utility Aging enforcementFiltering mechanism PrivateonlyCommissioning fundamentals Setup utility example one Setup utility example two Secure and nonsecure protocols FTP and Tftp Disabled Password encryptionManagement port Static IP entry for the OOB network management interface OOB network management port default IP flowchart Web management Device ManagerCommissioning fundamentals Commissioning Commissioning tasksCommissioning navigation Initial steps using Device Manager Initial commissioning proceduresEditing system information Initial commissioning navigationVariable definitions SaveBootConfig-saves the current Boot configurationSaveRuntimeConfig-saves the current Run-time configurationSaveSlaveBootConfig-saves Current boot configuration toFile to enable features Conﬁguring the date and timeChanging passwords Use the data in the following table to configure the CLI tab Variable Value Initial steps using the CLI Prerequisites to initial stepsInitial steps using the CLI Job aid Roadmap of initial CLI commands Initial steps using the CLI Connecting a terminal Procedure steps Connecting a modemPrerequisites Slip-compression truefalse slip-rx-compression truefalse Baud rate 8databits truefalse mode asciislippppMtu bytes my-ip ipaddr peer-ip ipaddr pppfile file Variable definitions Slip-rx-compression Procedure job aid PPP fileTruefalse Defaultroute Ipcpmaxconfigure valueAsyncmap value Chapfile fileLcpmaxconfigure value LoginIpcpmaxfailure value Ipcpmaxterminate valuePappasswd password Mtu valueNetmask value NoaccPaprestart value Papusername namePassivemode ProxyarpProcedure job aid setup utility prompts Conﬁguring the switch with the setup utilityChapfile mychap Papfile mypap Configuring the switch with the setup utility Initial steps using the CLI FTP Initial steps using the CLI Vlan Conﬁguring system identiﬁcation Enabledisable Mgmt-virtual-ip ipaddr/mask SendAuthenticationTrapSmlt-on-single-cp enabledisa Ble timer value Enabledisable EnablesDst-end Conﬁguring the time zoneMm.n.d/hhmmMMddhhmm Dst-start Mm.n.d/hhmmMMd Conﬁguring the dateDhhmm Specifying the primary SF/CPU Config bootconfig master cpu-slotCpu-slot Access level is an integer Access-level access levelEnabledisable enables or Logon or password Password is the passwordLogon and/or password applies Routing SwitchConfigures the minimum length For passwords in high-secureConfigures the operator logon to Previous passwords the switchResetting passwords Initial steps using the Nncli Initial steps using the Nncli Clock set MMddyyyyhhmmss Install Show boot config master Job aid Roadmap of initial Nncli commandsBoot config master cpu-slot Commissioning Log enablemaxfilesize CommunityForce GroupBoot config sio modem 8databitsbaud rate mode asciislipppp Boot config sio modem slip-compression slip-rx-comp ression Boot config sio modem restartConfigures the communication mode for Serial port. The default is American StandardIf you are configuring the modem port, you can Configure the port to use either the Slip orEnables or disables Transmission Control For Slip mode. The default is false. UseNo operator to remove this configuration. To Enables or disables TCP/IP header compressionDefaultroute Lcpmaxterminate value Novjccomp You must log on to the Privileged Exec mode in the Nncli Procedure job aid setup utility prompts Configuring the switch with the setup utility Initial steps using the Nncli FTP Initial steps using the Nncli Enables agent conformance mode Agent-conformanceAuthentication-trap BootstrapForce-iphdr-sender Force-trap-senderExample of configuring system identification To configure this option to the default Value, use the default operator withConfigures the starting date of DST Dst-end Mm.n.d/hhmmMMddhGreenwich. To configure this option to Default value, use the default operatorWith the command Clock set MMddyyyyhhmmssChanging passwords Access level word Changes the default lockout time after Three invalid attempts. ConfiguresConfigures the minimum length for Passwords in high-secure modeRemote connection conﬁguration using Device Manager Remote connection conﬁguration proceduresRemote connection configuration navigation Assigning an IP address to the management port Assigning static routes to the management interfaceVariable definitions Conﬁguring Snmp settings for Device Manager access Variable definitions Click System Flags Select the EnableWebServer box Enabling the Web management interfaceRemote connection configuration using Device Manager Remote connection conﬁguration using the CLI Remote connection configuration using the CLI Job aid Roadmap of remote connection CLI commands Config bootconfig net mgmt ip ipaddr/mask cpu-slot value Config sys set mgmt-virtual-ip ipaddr/maskGateway Config bootconfig net mgmt route add netaddr/mask gatewayNetaddr/mask Config bootconfig net mgmt route add 11.0.0.0/255.0.0.0 Enabling remote access servicesConfig bootconfig flags access-service truefalse Flags access-service truefalse Access-serviceConﬁguring the remote host logon Ftp-debugTftp-timeout Tftp-debugTftp-hash Tftp-rexmitRemote connection configuration using the CLI Remote connection conﬁguration using the Nncli Remote connection configuration using the Nncli Mask Job aid Roadmap of remote connection Nncli commandsAsk gateway Sys mgmt-virtual-ip ipaddr/mask Boot config net mgmt ip ipaddr mask value Web-serverBoot config net mgmt route netaddr/mask gateway Ipaddr maskEnabling remote access services Remote-access service types to Configuration. To configure this optionSpecifies one of the following Use the no operator to remove thisDef-display-rows Help-tftpManagement console screen. The default is disabled Use the no operator to later remove this configurationTftp-timeout Commissioning veriﬁcation Commissioning veriﬁcation navigationPinging an IP device Count valueUsing Telnet to log on to the device Accessing the switch through the Web interfaceAccessing the switch through the Web interface Commissioning verification Common procedure navigation Common procedures using Device ManagerSaving the conﬁguration Common procedures using Device Manager Common procedures using the CLI BackupMode clinncli FileSavetype StandbyCommon procedures using the Nncli File word Backup wordStandby word Index Time zone commands Page Commissioning