Manuals / Nortel Networks / Computer Equipment / Network Router

Nortel Networks 8600 manual Variable definitions

Models: 8600

1 136

Download 136 pages 14.91 Kb

Page 48

48Initial steps using the CLI

7Save the boot configuration.

8Reboot the switch.

--End--

Variable definitions

Use the data in the following table to use the config bootconfig sio command.

Variable	Value

8databits <truefalse>	Specifies either 8 (true) or 7 (false)
	data bits for each byte for software to
	interpret. The default is false.

baud <rate>	Configures the baud rate for the port.
	The default is 9600.

enable <truefalse>	Enables or disables the port. The
	default is true.

info	Displays information about the
	specified port.

mode <asciislipppp>	Configures the communication
	mode for the serial port. The default
	is American Standard Code for
	Information Interchange (ASCII).
	If you are configuring the modem
	port, you can configure the
	port to use the SLIP or the PPP
	communication mode.

mtu <bytes>	Configures the size of the maximum
	transmission unit for a PPP link
	(0–2048). The default is zero.

my-ip <ipaddr>	Configures the IP address for the
	server side, the Nortel Ethernet
	Routing Switch 8600, of the
	point-to-point link. The default is
	0.0.0.0. Nortel recommends that you
	use the current IP address for the
	management port.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319 01.01 Standard

30 May 2008

Copyright © 2008 Nortel Networks

Image 48

Nortel Networks 8600 manual Variable definitions

Contents

Commissioning Legal Notice Contents Initial steps using the Nncli Common procedures using Device Manager 127 Copyright 2008 Nortel Networks Software license Nortel Networks Inc. software license agreementGeneral Nortel Networks Inc. software license agreement Software license Features New in this releaseOther changes Document changesNew in this release Introduction NavigationIntroduction Commissioning fundamentals System connectionsTerminal connection Modem connectionPPP modem connection Data terminal Ready DTR Ground GND Data set readyRequest to send Clear to sendPPP configuration topology System logon Hsecure mode Default passwords and community stringsSetup utility Aging enforcementFiltering mechanism PrivateonlyCommissioning fundamentals Setup utility example one Setup utility example two Secure and nonsecure protocols Password encryption FTP and Tftp DisabledManagement port Static IP entry for the OOB network management interface OOB network management port default IP flowchart Web management Device ManagerCommissioning fundamentals Commissioning Commissioning tasksCommissioning navigation Initial steps using Device Manager Initial commissioning proceduresEditing system information Initial commissioning navigationVariable definitions SaveBootConfig-saves the current Boot configurationSaveRuntimeConfig-saves the current Run-time configurationSaveSlaveBootConfig-saves Current boot configuration toFile to enable features Conﬁguring the date and timeChanging passwords Use the data in the following table to configure the CLI tab Variable Value Initial steps using the CLI Prerequisites to initial stepsInitial steps using the CLI Job aid Roadmap of initial CLI commands Initial steps using the CLI Connecting a terminal Connecting a modem Procedure stepsPrerequisites Baud rate 8databits truefalse mode asciislipppp Slip-compression truefalse slip-rx-compression truefalseMtu bytes my-ip ipaddr peer-ip ipaddr pppfile file Variable definitions Procedure job aid PPP file Slip-rx-compressionTruefalse Defaultroute Ipcpmaxconfigure valueAsyncmap value Chapfile fileLcpmaxconfigure value LoginIpcpmaxfailure value Ipcpmaxterminate valuePappasswd password Mtu valueNetmask value NoaccPaprestart value Papusername namePassivemode ProxyarpConﬁguring the switch with the setup utility Procedure job aid setup utility promptsChapfile mychap Papfile mypap Configuring the switch with the setup utility Initial steps using the CLI FTP Initial steps using the CLI Vlan Conﬁguring system identiﬁcation Enabledisable Mgmt-virtual-ip ipaddr/mask SendAuthenticationTrapSmlt-on-single-cp enabledisa Ble timer value Enabledisable EnablesConﬁguring the time zone Dst-endMm.n.d/hhmmMMddhhmm Conﬁguring the date Dst-start Mm.n.d/hhmmMMdDhhmm Config bootconfig master cpu-slot Specifying the primary SF/CPUCpu-slot Access-level access level Access level is an integerEnabledisable enables or Logon or password Password is the passwordLogon and/or password applies Routing SwitchConfigures the minimum length For passwords in high-secureConfigures the operator logon to Previous passwords the switchResetting passwords Initial steps using the Nncli Initial steps using the Nncli Job aid Roadmap of initial Nncli commands Clock set MMddyyyyhhmmss Install Show boot config masterBoot config master cpu-slot Commissioning Log enablemaxfilesize CommunityForce GroupBoot config sio modem 8databitsbaud rate mode asciislipppp Boot config sio modem slip-compression slip-rx-comp ression Boot config sio modem restartConfigures the communication mode for Serial port. The default is American StandardIf you are configuring the modem port, you can Configure the port to use either the Slip orEnables or disables Transmission Control For Slip mode. The default is false. UseNo operator to remove this configuration. To Enables or disables TCP/IP header compressionDefaultroute Lcpmaxterminate value Novjccomp You must log on to the Privileged Exec mode in the Nncli Procedure job aid setup utility prompts Configuring the switch with the setup utility Initial steps using the Nncli FTP Initial steps using the Nncli Enables agent conformance mode Agent-conformanceAuthentication-trap BootstrapForce-iphdr-sender Force-trap-senderExample of configuring system identification To configure this option to the default Value, use the default operator withConfigures the starting date of DST Dst-end Mm.n.d/hhmmMMddhGreenwich. To configure this option to Default value, use the default operatorWith the command Clock set MMddyyyyhhmmssChanging passwords Access level word Changes the default lockout time after Three invalid attempts. ConfiguresConfigures the minimum length for Passwords in high-secure modeRemote connection conﬁguration using Device Manager Remote connection conﬁguration proceduresRemote connection configuration navigation Assigning an IP address to the management port Assigning static routes to the management interfaceVariable definitions Conﬁguring Snmp settings for Device Manager access Variable definitions Click System Flags Select the EnableWebServer box Enabling the Web management interfaceRemote connection configuration using Device Manager Remote connection conﬁguration using the CLI Remote connection configuration using the CLI Job aid Roadmap of remote connection CLI commands Config bootconfig net mgmt ip ipaddr/mask cpu-slot value Config sys set mgmt-virtual-ip ipaddr/maskConfig bootconfig net mgmt route add netaddr/mask gateway GatewayNetaddr/mask Enabling remote access services Config bootconfig net mgmt route add 11.0.0.0/255.0.0.0Config bootconfig flags access-service truefalse Flags access-service truefalse Access-serviceConﬁguring the remote host logon Ftp-debugTftp-timeout Tftp-debugTftp-hash Tftp-rexmitRemote connection configuration using the CLI Remote connection conﬁguration using the Nncli Remote connection configuration using the Nncli Job aid Roadmap of remote connection Nncli commands MaskAsk gateway Sys mgmt-virtual-ip ipaddr/mask Boot config net mgmt ip ipaddr mask value Web-serverBoot config net mgmt route netaddr/mask gateway Ipaddr maskEnabling remote access services Remote-access service types to Configuration. To configure this optionSpecifies one of the following Use the no operator to remove thisDef-display-rows Help-tftpManagement console screen. The default is disabled Use the no operator to later remove this configurationTftp-timeout Commissioning veriﬁcation Commissioning veriﬁcation navigationPinging an IP device Count valueUsing Telnet to log on to the device Accessing the switch through the Web interfaceAccessing the switch through the Web interface Commissioning verification Common procedures using Device Manager Common procedure navigationSaving the conﬁguration Common procedures using Device Manager Common procedures using the CLI BackupMode clinncli FileSavetype StandbyCommon procedures using the Nncli Backup word File wordStandby word Index Time zone commands Page Commissioning