Manuals / Nortel Networks / Computer Equipment / Network Router

Nortel Networks 8600 manual Commissioning fundamentals

Models: 8600

1 136

Download 136 pages 14.91 Kb

Page 22

22Commissioning fundamentals

the switch reboots in the desired operating mode. The setup utility also provides error and warning messages to advise you of the ramifications of certain hardware and software configurations.

For information about the supported operating modes, see Nortel Ethernet Routing Switch 8600 Administration, NN46205-605.

The setup utility prompts you through the configuration process by asking a series of questions. Answer each question or accept the default by pressing Enter. Each question shows the default in brackets ([ ]) and the acceptable parameter options in parenthesis.

After you run the setup utility, reboot the switch.

The following figures show sample output from the setup utility. This example uses the default values.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319 01.01 Standard

30 May 2008

Copyright © 2008 Nortel Networks

Image 22

Nortel Networks 8600 manual Commissioning fundamentals

Contents

Commissioning Legal Notice Contents Initial steps using the Nncli Common procedures using Device Manager 127 Copyright 2008 Nortel Networks Software license Nortel Networks Inc. software license agreementGeneral Nortel Networks Inc. software license agreement Software license Other changes FeaturesNew in this release Document changesNew in this release Introduction NavigationIntroduction Commissioning fundamentals System connectionsTerminal connection Modem connectionRequest to send PPP modem connectionData terminal Ready DTR Ground GND Data set ready Clear to sendPPP configuration topology System logon Hsecure mode Default passwords and community stringsFiltering mechanism Setup utilityAging enforcement PrivateonlyCommissioning fundamentals Setup utility example one Setup utility example two Secure and nonsecure protocols FTP and Tftp Disabled Password encryptionManagement port Static IP entry for the OOB network management interface OOB network management port default IP flowchart Web management Device ManagerCommissioning fundamentals Commissioning Commissioning tasksCommissioning navigation Initial steps using Device Manager Initial commissioning proceduresEditing system information Initial commissioning navigationVariable definitions SaveRuntimeConfig-saves the current SaveBootConfig-saves the currentBoot configuration Run-time configurationFile to enable features SaveSlaveBootConfig-savesCurrent boot configuration to Conﬁguring the date and timeChanging passwords Use the data in the following table to configure the CLI tab Variable Value Initial steps using the CLI Prerequisites to initial stepsInitial steps using the CLI Job aid Roadmap of initial CLI commands Initial steps using the CLI Connecting a terminal Procedure steps Connecting a modemPrerequisites Slip-compression truefalse slip-rx-compression truefalse Baud rate 8databits truefalse mode asciislippppMtu bytes my-ip ipaddr peer-ip ipaddr pppfile file Variable definitions Slip-rx-compression Procedure job aid PPP fileTruefalse Asyncmap value DefaultrouteIpcpmaxconfigure value Chapfile fileIpcpmaxfailure value Lcpmaxconfigure valueLogin Ipcpmaxterminate valueNetmask value Pappasswd passwordMtu value NoaccPassivemode Paprestart valuePapusername name ProxyarpProcedure job aid setup utility prompts Conﬁguring the switch with the setup utilityChapfile mychap Papfile mypap Configuring the switch with the setup utility Initial steps using the CLI FTP Initial steps using the CLI Vlan Conﬁguring system identiﬁcation Smlt-on-single-cp enabledisa Enabledisable Mgmt-virtual-ip ipaddr/maskSendAuthenticationTrap Ble timer value Enabledisable EnablesDst-end Conﬁguring the time zoneMm.n.d/hhmmMMddhhmm Dst-start Mm.n.d/hhmmMMd Conﬁguring the dateDhhmm Specifying the primary SF/CPU Config bootconfig master cpu-slotCpu-slot Access level is an integer Access-level access levelEnabledisable enables or Logon and/or password applies Logon or passwordPassword is the password Routing SwitchConfigures the operator logon to Configures the minimum lengthFor passwords in high-secure Previous passwords the switchResetting passwords Initial steps using the Nncli Initial steps using the Nncli Clock set MMddyyyyhhmmss Install Show boot config master Job aid Roadmap of initial Nncli commandsBoot config master cpu-slot Commissioning Force Log enablemaxfilesizeCommunity GroupBoot config sio modem 8databitsbaud rate mode asciislipppp Boot config sio modem slip-compression slip-rx-comp ression Boot config sio modem restartIf you are configuring the modem port, you can Configures the communication mode forSerial port. The default is American Standard Configure the port to use either the Slip orNo operator to remove this configuration. To Enables or disables Transmission ControlFor Slip mode. The default is false. Use Enables or disables TCP/IP header compressionDefaultroute Lcpmaxterminate value Novjccomp You must log on to the Privileged Exec mode in the Nncli Procedure job aid setup utility prompts Configuring the switch with the setup utility Initial steps using the Nncli FTP Initial steps using the Nncli Enables agent conformance mode Agent-conformanceForce-iphdr-sender Authentication-trapBootstrap Force-trap-senderExample of configuring system identification Configures the starting date of DST To configure this option to the defaultValue, use the default operator with Dst-end Mm.n.d/hhmmMMddhWith the command Greenwich. To configure this option toDefault value, use the default operator Clock set MMddyyyyhhmmssChanging passwords Access level word Configures the minimum length for Changes the default lockout time afterThree invalid attempts. Configures Passwords in high-secure modeRemote connection conﬁguration using Device Manager Remote connection conﬁguration proceduresRemote connection configuration navigation Assigning an IP address to the management port Assigning static routes to the management interfaceVariable definitions Conﬁguring Snmp settings for Device Manager access Variable definitions Click System Flags Select the EnableWebServer box Enabling the Web management interfaceRemote connection configuration using Device Manager Remote connection conﬁguration using the CLI Remote connection configuration using the CLI Job aid Roadmap of remote connection CLI commands Config bootconfig net mgmt ip ipaddr/mask cpu-slot value Config sys set mgmt-virtual-ip ipaddr/maskGateway Config bootconfig net mgmt route add netaddr/mask gatewayNetaddr/mask Config bootconfig net mgmt route add 11.0.0.0/255.0.0.0 Enabling remote access servicesConfig bootconfig flags access-service truefalse Flags access-service truefalse Access-serviceConﬁguring the remote host logon Ftp-debugTftp-hash Tftp-timeoutTftp-debug Tftp-rexmitRemote connection configuration using the CLI Remote connection conﬁguration using the Nncli Remote connection configuration using the Nncli Mask Job aid Roadmap of remote connection Nncli commandsAsk gateway Sys mgmt-virtual-ip ipaddr/mask Boot config net mgmt ip ipaddr mask value Web-serverBoot config net mgmt route netaddr/mask gateway Ipaddr maskEnabling remote access services Specifies one of the following Remote-access service types toConfiguration. To configure this option Use the no operator to remove thisDef-display-rows Help-tftpManagement console screen. The default is disabled Use the no operator to later remove this configurationTftp-timeout Pinging an IP device Commissioning veriﬁcationCommissioning veriﬁcation navigation Count valueUsing Telnet to log on to the device Accessing the switch through the Web interfaceAccessing the switch through the Web interface Commissioning verification Common procedure navigation Common procedures using Device ManagerSaving the conﬁguration Common procedures using Device Manager Common procedures using the CLI BackupSavetype Mode clinncliFile StandbyCommon procedures using the Nncli File word Backup wordStandby word Index Time zone commands Page Commissioning