Manuals / Nortel Networks / Computer Equipment / Network Router

Nortel Networks 8600 manual Ftp

Models: 8600

1 136

Download 136 pages 14.91 Kb

Page 57

Configuring the switch with the setup utility 57

Table 9

Job aid: Setup utility prompt descriptions (cont’d.)

Prompt	Description and action

Do you want to enable CPU	Description: Specifies if you want to enable
High Availability mode [n]	CPU high availability (HA) mode. Use CPU
(y/n)?	HA mode to recover switches with two CPUs
	quickly from a failure of one of the CPUs. In
	HA mode (hot standby), you synchronize and
	configure the two CPUs in the same mode, so
	they are compatible.
	Action: Specify y to enable CPU high
	availability (HA) mode. Accept the default (n),
	to not enable CPU HA mode.

Do you want to enable	Description: Specifies if you want to enable
vlan-optimization-mode support	support for the VLAN optimization mode.
[n] (y/n) ?
	Action: Specify y to enable VLAN
	optimization mode support. Accept the
	default (n) to not enable VLAN optimization
	mode support.

Do you want to enable r-mode	Description: Specifies if you want to enable
support [n] (y/n) ?	support for the R mode support.
	Action: Specify y to enable R mode support.
	Accept the default (n) to not enable R mode
	support.

Do you want to enable FTP [n]	Description: Specifies if you want users to
(y/n)?	access the switch by File transfer Protocol
	(FTP).
	Action: Enter y to enable FTP for remote
	users. Accept the default (n) to not enable
	FTP.

Do you want to enable	Description: Specifies if you want to access
RLOGIN [n] (y/n)?	the switch by Rlogin.
	Action: Enter y to enable Rlogin for remote
	users. Accept the default (n) to not enable
	Rlogin.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319 01.01 Standard

30 May 2008

Copyright © 2008 Nortel Networks

Image 57

Nortel Networks 8600 manual Ftp

Contents

Commissioning Legal Notice Contents Initial steps using the Nncli Common procedures using Device Manager 127 Copyright 2008 Nortel Networks Nortel Networks Inc. software license agreement Software licenseGeneral Nortel Networks Inc. software license agreement Software license New in this release FeaturesOther changes Document changesNew in this release Navigation IntroductionIntroduction System connections Commissioning fundamentalsModem connection Terminal connectionData terminal Ready DTR Ground GND Data set ready PPP modem connectionRequest to send Clear to sendPPP configuration topology System logon Default passwords and community strings Hsecure modeAging enforcement Setup utilityFiltering mechanism PrivateonlyCommissioning fundamentals Setup utility example one Setup utility example two Secure and nonsecure protocols Password encryption FTP and Tftp DisabledManagement port Static IP entry for the OOB network management interface OOB network management port default IP flowchart Device Manager Web managementCommissioning fundamentals Commissioning tasks CommissioningCommissioning navigation Initial commissioning procedures Initial steps using Device ManagerInitial commissioning navigation Editing system informationVariable definitions Boot configuration SaveBootConfig-saves the currentSaveRuntimeConfig-saves the current Run-time configurationCurrent boot configuration to SaveSlaveBootConfig-savesFile to enable features Conﬁguring the date and timeChanging passwords Use the data in the following table to configure the CLI tab Variable Value Prerequisites to initial steps Initial steps using the CLIInitial steps using the CLI Job aid Roadmap of initial CLI commands Initial steps using the CLI Connecting a terminal Connecting a modem Procedure stepsPrerequisites Baud rate 8databits truefalse mode asciislipppp Slip-compression truefalse slip-rx-compression truefalseMtu bytes my-ip ipaddr peer-ip ipaddr pppfile file Variable definitions Procedure job aid PPP file Slip-rx-compressionTruefalse Ipcpmaxconfigure value DefaultrouteAsyncmap value Chapfile fileLogin Lcpmaxconfigure valueIpcpmaxfailure value Ipcpmaxterminate valueMtu value Pappasswd passwordNetmask value NoaccPapusername name Paprestart valuePassivemode ProxyarpConﬁguring the switch with the setup utility Procedure job aid setup utility promptsChapfile mychap Papfile mypap Configuring the switch with the setup utility Initial steps using the CLI FTP Initial steps using the CLI Vlan Conﬁguring system identiﬁcation SendAuthenticationTrap Enabledisable Mgmt-virtual-ip ipaddr/maskSmlt-on-single-cp enabledisa Ble timer value Enabledisable EnablesConﬁguring the time zone Dst-endMm.n.d/hhmmMMddhhmm Conﬁguring the date Dst-start Mm.n.d/hhmmMMdDhhmm Config bootconfig master cpu-slot Specifying the primary SF/CPUCpu-slot Access-level access level Access level is an integerEnabledisable enables or Password is the password Logon or passwordLogon and/or password applies Routing SwitchFor passwords in high-secure Configures the minimum lengthConfigures the operator logon to Previous passwords the switchResetting passwords Initial steps using the Nncli Initial steps using the Nncli Job aid Roadmap of initial Nncli commands Clock set MMddyyyyhhmmss Install Show boot config masterBoot config master cpu-slot Commissioning Community Log enablemaxfilesizeForce GroupBoot config sio modem 8databitsbaud rate mode asciislipppp Boot config sio modem restart Boot config sio modem slip-compression slip-rx-comp ressionSerial port. The default is American Standard Configures the communication mode forIf you are configuring the modem port, you can Configure the port to use either the Slip orFor Slip mode. The default is false. Use Enables or disables Transmission ControlNo operator to remove this configuration. To Enables or disables TCP/IP header compressionDefaultroute Lcpmaxterminate value Novjccomp You must log on to the Privileged Exec mode in the Nncli Procedure job aid setup utility prompts Configuring the switch with the setup utility Initial steps using the Nncli FTP Initial steps using the Nncli Agent-conformance Enables agent conformance modeBootstrap Authentication-trapForce-iphdr-sender Force-trap-senderExample of configuring system identification Value, use the default operator with To configure this option to the defaultConfigures the starting date of DST Dst-end Mm.n.d/hhmmMMddhDefault value, use the default operator Greenwich. To configure this option toWith the command Clock set MMddyyyyhhmmssChanging passwords Access level word Three invalid attempts. Configures Changes the default lockout time afterConfigures the minimum length for Passwords in high-secure modeRemote connection conﬁguration procedures Remote connection conﬁguration using Device ManagerRemote connection configuration navigation Assigning static routes to the management interface Assigning an IP address to the management portVariable definitions Conﬁguring Snmp settings for Device Manager access Variable definitions Enabling the Web management interface Click System Flags Select the EnableWebServer boxRemote connection configuration using Device Manager Remote connection conﬁguration using the CLI Remote connection configuration using the CLI Job aid Roadmap of remote connection CLI commands Config sys set mgmt-virtual-ip ipaddr/mask Config bootconfig net mgmt ip ipaddr/mask cpu-slot valueConfig bootconfig net mgmt route add netaddr/mask gateway GatewayNetaddr/mask Enabling remote access services Config bootconfig net mgmt route add 11.0.0.0/255.0.0.0Config bootconfig flags access-service truefalse Access-service Flags access-service truefalseFtp-debug Conﬁguring the remote host logonTftp-debug Tftp-timeoutTftp-hash Tftp-rexmitRemote connection configuration using the CLI Remote connection conﬁguration using the Nncli Remote connection configuration using the Nncli Job aid Roadmap of remote connection Nncli commands MaskAsk gateway Sys mgmt-virtual-ip ipaddr/mask Web-server Boot config net mgmt ip ipaddr mask valueIpaddr mask Boot config net mgmt route netaddr/mask gatewayEnabling remote access services Configuration. To configure this option Remote-access service types toSpecifies one of the following Use the no operator to remove thisHelp-tftp Def-display-rowsUse the no operator to later remove this configuration Management console screen. The default is disabledTftp-timeout Commissioning veriﬁcation navigation Commissioning veriﬁcationPinging an IP device Count valueAccessing the switch through the Web interface Using Telnet to log on to the deviceAccessing the switch through the Web interface Commissioning verification Common procedures using Device Manager Common procedure navigationSaving the conﬁguration Common procedures using Device Manager Backup Common procedures using the CLIFile Mode clinncliSavetype StandbyCommon procedures using the Nncli Backup word File wordStandby word Index Time zone commands Page Commissioning