Manuals / Nortel Networks / Computer Equipment / Network Router

Nortel Networks 8600 manual Specifies one of the following, Remote-access service types to

Models: 8600

1 136

Download 136 pages 14.91 Kb

Page 119

Enabling the Web management interface 119

Procedure steps

Step Action

1Enable the access service by using the following command: boot config flags <access-service>

See the following variable definitions table for more information.

2Save the boot configuration.

--End--

Variable definitions

Use the data in the following table to use the boot config flags command.

Variable	Value

access-service	Specifies one of the following
	remote-access service types to
	enable:
	•	ftpd
	•	rlogind
	•	sshd
	•	telnetd
	•	tftpd
	Use the no operator to remove this
	configuration. To configure this option
	to the default value, use the default
	operator with the command.

Enabling the Web management interface

Enable the Web management interface to provide management access to the switch using a Web browser.

Prerequisites

•You must log on to the Global Configuration mode in the NNCLI.

Procedure steps

Step Action

1Enable the Web server by using the following command:

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319 01.01 Standard

30 May 2008

Copyright © 2008 Nortel Networks

Image 119

Nortel Networks 8600 Specifies one of the following, Remote-access service types to, Use the no operator to remove this

Contents

Commissioning Legal Notice Contents Initial steps using the Nncli Common procedures using Device Manager 127 Copyright 2008 Nortel Networks Nortel Networks Inc. software license agreement Software licenseGeneral Nortel Networks Inc. software license agreement Software license Document changes FeaturesNew in this release Other changesNew in this release Navigation IntroductionIntroduction System connections Commissioning fundamentalsModem connection Terminal connectionClear to send PPP modem connectionData terminal Ready DTR Ground GND Data set ready Request to sendPPP configuration topology System logon Default passwords and community strings Hsecure modePrivateonly Setup utilityAging enforcement Filtering mechanismCommissioning fundamentals Setup utility example one Setup utility example two Secure and nonsecure protocols Management port Password encryptionFTP and Tftp Disabled Static IP entry for the OOB network management interface OOB network management port default IP flowchart Device Manager Web managementCommissioning fundamentals Commissioning tasks CommissioningCommissioning navigation Initial commissioning procedures Initial steps using Device ManagerInitial commissioning navigation Editing system informationVariable definitions Run-time configuration SaveBootConfig-saves the currentBoot configuration SaveRuntimeConfig-saves the currentConﬁguring the date and time SaveSlaveBootConfig-savesCurrent boot configuration to File to enable featuresChanging passwords Use the data in the following table to configure the CLI tab Variable Value Prerequisites to initial steps Initial steps using the CLIInitial steps using the CLI Job aid Roadmap of initial CLI commands Initial steps using the CLI Connecting a terminal Prerequisites Connecting a modemProcedure steps Mtu bytes my-ip ipaddr peer-ip ipaddr pppfile file Baud rate 8databits truefalse mode asciislippppSlip-compression truefalse slip-rx-compression truefalse Variable definitions Truefalse Procedure job aid PPP fileSlip-rx-compression Chapfile file DefaultrouteIpcpmaxconfigure value Asyncmap valueIpcpmaxterminate value Lcpmaxconfigure valueLogin Ipcpmaxfailure valueNoacc Pappasswd passwordMtu value Netmask valueProxyarp Paprestart valuePapusername name PassivemodeChapfile mychap Papfile mypap Conﬁguring the switch with the setup utilityProcedure job aid setup utility prompts Configuring the switch with the setup utility Initial steps using the CLI FTP Initial steps using the CLI Vlan Conﬁguring system identiﬁcation Ble timer value Enabledisable Enables Enabledisable Mgmt-virtual-ip ipaddr/maskSendAuthenticationTrap Smlt-on-single-cp enabledisaMm.n.d/hhmmMMddhhmm Conﬁguring the time zoneDst-end Dhhmm Conﬁguring the dateDst-start Mm.n.d/hhmmMMd Cpu-slot Config bootconfig master cpu-slotSpecifying the primary SF/CPU Enabledisable enables or Access-level access levelAccess level is an integer Routing Switch Logon or passwordPassword is the password Logon and/or password appliesPrevious passwords the switch Configures the minimum lengthFor passwords in high-secure Configures the operator logon toResetting passwords Initial steps using the Nncli Initial steps using the Nncli Boot config master cpu-slot Job aid Roadmap of initial Nncli commandsClock set MMddyyyyhhmmss Install Show boot config master Commissioning Group Log enablemaxfilesizeCommunity ForceBoot config sio modem 8databitsbaud rate mode asciislipppp Boot config sio modem restart Boot config sio modem slip-compression slip-rx-comp ressionConfigure the port to use either the Slip or Configures the communication mode forSerial port. The default is American Standard If you are configuring the modem port, you canEnables or disables TCP/IP header compression Enables or disables Transmission ControlFor Slip mode. The default is false. Use No operator to remove this configuration. ToDefaultroute Lcpmaxterminate value Novjccomp You must log on to the Privileged Exec mode in the Nncli Procedure job aid setup utility prompts Configuring the switch with the setup utility Initial steps using the Nncli FTP Initial steps using the Nncli Agent-conformance Enables agent conformance modeForce-trap-sender Authentication-trapBootstrap Force-iphdr-senderExample of configuring system identification Dst-end Mm.n.d/hhmmMMddh To configure this option to the defaultValue, use the default operator with Configures the starting date of DSTClock set MMddyyyyhhmmss Greenwich. To configure this option toDefault value, use the default operator With the commandChanging passwords Access level word Passwords in high-secure mode Changes the default lockout time afterThree invalid attempts. Configures Configures the minimum length forRemote connection conﬁguration procedures Remote connection conﬁguration using Device ManagerRemote connection configuration navigation Assigning static routes to the management interface Assigning an IP address to the management portVariable definitions Conﬁguring Snmp settings for Device Manager access Variable definitions Enabling the Web management interface Click System Flags Select the EnableWebServer boxRemote connection configuration using Device Manager Remote connection conﬁguration using the CLI Remote connection configuration using the CLI Job aid Roadmap of remote connection CLI commands Config sys set mgmt-virtual-ip ipaddr/mask Config bootconfig net mgmt ip ipaddr/mask cpu-slot valueNetaddr/mask Config bootconfig net mgmt route add netaddr/mask gatewayGateway Config bootconfig flags access-service truefalse Enabling remote access servicesConfig bootconfig net mgmt route add 11.0.0.0/255.0.0.0 Access-service Flags access-service truefalseFtp-debug Conﬁguring the remote host logonTftp-rexmit Tftp-timeoutTftp-debug Tftp-hashRemote connection configuration using the CLI Remote connection conﬁguration using the Nncli Remote connection configuration using the Nncli Ask gateway Sys mgmt-virtual-ip ipaddr/mask Job aid Roadmap of remote connection Nncli commandsMask Web-server Boot config net mgmt ip ipaddr mask valueIpaddr mask Boot config net mgmt route netaddr/mask gatewayEnabling remote access services Use the no operator to remove this Remote-access service types toConfiguration. To configure this option Specifies one of the followingHelp-tftp Def-display-rowsUse the no operator to later remove this configuration Management console screen. The default is disabledTftp-timeout Count value Commissioning veriﬁcationCommissioning veriﬁcation navigation Pinging an IP deviceAccessing the switch through the Web interface Using Telnet to log on to the deviceAccessing the switch through the Web interface Commissioning verification Saving the conﬁguration Common procedures using Device ManagerCommon procedure navigation Common procedures using Device Manager Backup Common procedures using the CLIStandby Mode clinncliFile SavetypeCommon procedures using the Nncli Standby word Backup wordFile word Index Time zone commands Page Commissioning