Factory Defaults, Reboot | Olitec RW400SG manual

5.11.3Factory Defaults

If the router is not experiencing difficulties, there is no need to download a more recent firmware version, unless that version has a new feature that you want to use.

Note: When you upgrade the router's firmware, you may lose its configuration settings, so make sure you write down the router settings before you upgrade its firmware.

To upgrade the router's firmware, follow these instructions:

1.Download a more recent firmware upgrade file.

2.Run a TFTP Server on a PC on your LAN, and take the file in the TFTP server’s path.

3.Type the downloaded file name into the File Name box.

4.Type the IP Address of the PC that runs the TFTP server in the TFTP Server’s IP Address field.

5.Click the Upgrade button.

¾Firmware Version - displays the current firmware version.

¾Hardware Version - displays the current hardware version. The hardware version of the upgrade file must accord with the current hardware version.

Note:

1.Do not turn off the router or press the Reset button while the firmware is being upgraded.

2.The router will reboot after the Upgrading has been finished.

5.11.3Factory Defaults

This page (shown in figure 5-41) allows you to restore the factory default settings for the router.

Figure 5-41: Restore Factory Default

Click the Restore button to reset all configuration settings to their default values.

•The default User Name: admin

•The default Password: admin

•The default IP Address: 192.168.1.1

•The default Subnet Mask: 255.255.255.0

Note: Any settings you have saved will be lost when the default settings are restored.

5.11.4 Reboot

This page (shown in figure 5-42) allows you to reboot the router.

- 46 -

Image 50

Olitec RW400SG manual Factory Defaults, Reboot

Contents

RW400SG Router OLITEC Users GuidePage 5.6.1 DHCP Settings Appendix B Configuring the PCs 5.11.3 Factory DefaultsAppendix A FAQ Appendix C Specifications 2.1 Overview of the Router 2.2 FeaturesChapter 2 Introduction 2.3 Panel Layout 2.3.1 The Front Panel 2.3.2 The Rear Panel 3.3 Connecting the Router Chapter 3 Connecting the Router3.2 Installation Environment Requirements 3.1 System Requirements To LAN Switch/Hub（XDSL 、Cable 、Ethernet ） To WAN Chapter 4 Quick Installation Guide 4.1 TCP/IP configuration 4.2 Quick Installation Guide Figure 4-6 Choose WAN Connection Type Figure 4-4 Login WindowsFigure 4-5 Quick Setup If you choose PPPoE, you will see this page shown in figure Figure 4-7 Quick Setup - PPPoE In this page, you can configure the following wireless parameters 2. Wireless Chapter 5 Configuring the Router5.1 login Radio, SSID, Channel, Mode, Wireless MAC address and IP address Please refer to Section 4.2 Quick Installation Guide 5.3 Quick Setup5.4 Network Figure 5-1 Router Status 5.4.1 LAN 5.4.2 WAN Figure 5-4 WAN - Dynamic IP Figure 5-5 WAN - Static IP Click Logout button to end 802.1x authenticationFigure 5-4a WAN - 802.1X + Dynamic IP You should type the following parameters into the spaces provided Figure 5-5a WAN - 802.1X + Static IP Click Login to start 802.1x authenticationClick Logout to end 802.1x authentication Figure 5-6 WAN - PPPoE Figure 5-7 PPPoE Advanced Settings 5.4.3 MAC Clone 5.5 Wireless 5.5.1 Wireless Settings ¾ Mode - Select the desired wireless mode. The options are Encryptions 5.5.2 MAC Filtering Figure 5-12 Add or Modify Wireless MAC Address Filtering entry 5.5.3 Wireless Statistics 5.6.1 DHCP Settings 5.6 DHCP 5.6.2 DHCP Clients List To modify A Reserved IP address 5.6.3 Address ReservationTo Reserve IP addresses To delete all Reserved IP addresses 5.7 Forwarding 5.7.1 Virtual Servers To delete all service entries To setup a virtual server entryTo delete a service entry To modify a virtual server entry Figure 5-20 Port Triggering Once configured, operation is as follows To delete all rules Modifying an existing ruleDeleting an existing rule 5.7.3 DMZ 5.7.4 UPnP 5.8 Security 5.8.1 Firewall 5.8.2 IP Address Filtering 5.8.3 Domain Filtering Figure 5-28 Add or Modify a Domain Filtering entry Click the Enabled All button to make all entries enabledFigure 5-27 Domain Filtering To add or modify a Domain Filtering entry, follow these instructions 5.8.4 MAC Filtering 5.8.5 Remote Management 5.8.6 Advanced Security Click the Save button to save the settings To modify an existing entry 5.9 Static RoutingTo add static routing entries 1. Modify the entry’s Destination IP Address, Subnet Mask and Gateway 5.10.1 Dyndns.org DDNS 5.10 DDNSTo delete all the entries 5.10.2 Oray.net DDNS 5.10.3 Comexe.cn DDNS 5.11 System Tools 5.11.1 Time 5.11.2 Firmware 5.11.3 Factory Defaults 5.11.4 Reboot 5.11.5 Password Statistics Table 5.11.6 Log5.11.7 Statistics Click the Refresh button to refresh immediately The total amount of packets received and transmitted by the router Appendix A FAQ 1. How do I configure the router to access Internet by ADSL users? 3. I want to use Netmeeting, what do I need to do? 4. I want to build a WEB Server on the LAN, what should I do? 5. The wireless stations cannot connect to the router 2. Configure TCP/IP for your computer Appendix B Configuring the PCs1. Install TCP/IP component Assigned by DHCP Sever Figure B-5 Gateway tab Setting IP address manuallyFigure B-6 DNS Configuration tab Figure B-7 IP Address tab Figure B-8 Gateway tab click Add button. Shown below Figure B-9 DNS Configuration tab Appendix C Specifications General Appendix D Glossary ¾ Domain Name - A descriptive name for an address or group of addresses on the Internet