Users Guide
RW400SG Router OLITEC
Page
5.6.1 DHCP Settings
Appendix A FAQ
5.11.3 Factory Defaults
Appendix B Configuring the PCs
Appendix C Specifications
2.1 Overview of the Router
2.2 Features
Chapter 2 Introduction
2.3.1 The Front Panel
2.3 Panel Layout
2.3.2 The Rear Panel
3.2 Installation Environment Requirements
Chapter 3 Connecting the Router
3.3 Connecting the Router
3.1 System Requirements
（XDSL 、Cable 、Ethernet ）
Switch/Hub
To LAN
To WAN
4.1 TCP/IP configuration
Chapter 4 Quick Installation Guide
4.2 Quick Installation Guide
Figure 4-5 Quick Setup
Figure 4-4 Login Windows
Figure 4-6 Choose WAN Connection Type
If you choose PPPoE, you will see this page shown in figure
Figure 4-7 Quick Setup - PPPoE
In this page, you can configure the following wireless parameters
5.1 login
Chapter 5 Configuring the Router
2. Wireless
Radio, SSID, Channel, Mode, Wireless MAC address and IP address
5.4 Network
5.3 Quick Setup
Please refer to Section 4.2 Quick Installation Guide
Figure 5-1 Router Status
5.4.2 WAN
5.4.1 LAN
Figure 5-4 WAN - Dynamic IP
Figure 5-4a WAN - 802.1X + Dynamic IP
Click Logout button to end 802.1x authentication
Figure 5-5 WAN - Static IP
You should type the following parameters into the spaces provided
Click Logout to end 802.1x authentication
Click Login to start 802.1x authentication
Figure 5-5a WAN - 802.1X + Static IP
Figure 5-6 WAN - PPPoE
Figure 5-7 PPPoE Advanced Settings
5.4.3 MAC Clone
5.5.1 Wireless Settings
5.5 Wireless
¾ Mode - Select the desired wireless mode. The options are
Encryptions
5.5.2 MAC Filtering
Figure 5-12 Add or Modify Wireless MAC Address Filtering entry
5.5.3 Wireless Statistics
5.6 DHCP
5.6.1 DHCP Settings
5.6.2 DHCP Clients List
To Reserve IP addresses
5.6.3 Address Reservation
To modify A Reserved IP address
To delete all Reserved IP addresses
5.7.1 Virtual Servers
5.7 Forwarding
To delete a service entry
To setup a virtual server entry
To delete all service entries
To modify a virtual server entry
Figure 5-20 Port Triggering Once configured, operation is as follows
Deleting an existing rule
Modifying an existing rule
To delete all rules
5.7.3 DMZ
5.7.4 UPnP
5.8.1 Firewall
5.8 Security
5.8.2 IP Address Filtering
5.8.3 Domain Filtering
Figure 5-27 Domain Filtering
Click the Enabled All button to make all entries enabled
Figure 5-28 Add or Modify a Domain Filtering entry
To add or modify a Domain Filtering entry, follow these instructions
5.8.4 MAC Filtering
5.8.5 Remote Management
5.8.6 Advanced Security
Click the Save button to save the settings
To add static routing entries
5.9 Static Routing
To modify an existing entry
1. Modify the entry’s Destination IP Address, Subnet Mask and Gateway
To delete all the entries
5.10 DDNS
5.10.1 Dyndns.org DDNS
5.10.2 Oray.net DDNS
5.10.3 Comexe.cn DDNS
5.11 System Tools
5.11.2 Firmware
5.11.1 Time
5.11.4 Reboot
5.11.3 Factory Defaults
5.11.5 Password
Statistics Table
5.11.6 Log
5.11.7 Statistics
The total amount of packets received and transmitted by the router
Click the Refresh button to refresh immediately
1. How do I configure the router to access Internet by ADSL users?
Appendix A FAQ
3. I want to use Netmeeting, what do I need to do?
4. I want to build a WEB Server on the LAN, what should I do?
5. The wireless stations cannot connect to the router
2. Configure TCP/IP for your computer
Appendix B Configuring the PCs
1. Install TCP/IP component
Assigned by DHCP Sever
Figure B-5 Gateway tab
Setting IP address manually
Figure B-6 DNS Configuration tab
Figure B-8 Gateway tab
Figure B-7 IP Address tab
click Add button. Shown below Figure B-9 DNS Configuration tab
General
Appendix C Specifications
Appendix D Glossary
¾ Domain Name - A descriptive name for an address or group of addresses on the Internet
