Configuring the Router, Login, Status, Lan, Wan | Olitec RW400SG

Chapter 5: Configuring the Router

This chapter describes each web page's key functions.

5.1 login

After your successful login, you can configure and manage the router. There are ten main menus on the left of the web-based utility. Submenus will be available after you click one of the main menus. The ten main menus are: Status, Quick Setup, Network, Wireless, DHCP, Forwarding, Security, Static Routing, DDNS and System Tools. On the right of the web-based utility, there are the detailed explanations and instructions for the corresponding page. To apply any settings you have altered on the page, please click the Save button.

There are the detailed explanations for each web page's key functions below.

5.2 Status

The Status page displays the router's current status and configuration. All information is read-only.

1.LAN

This field displays the current settings or information for the LAN, including the MAC address, IP address and Subnet Mask.

2.Wireless

This field displays basic information or status for wireless function, including Wireless

Radio, SSID, Channel, Mode, Wireless MAC address and IP address.

3.WAN

These parameters apply to the WAN port of the router, including MAC address, IP address, Subnet Mask, Default Gateway, DNS server and WAN connection type. If PPPoE is chosen as the WAN connection type, the Disconnect button will be shown here while you are accessing the Internet. You can also cut the connection by clicking the button. If you have not connected to the Internet, a Connect button will be shown, you can then establish the connection by clicking the button.

4.Traffic Statistics

This field displays the router's traffic statistics.

5.System Up Time

The time of the router running from it's powered on or reset.

- 11 -

Image 15

Olitec RW400SG manual Configuring the Router, login, Status, Lan, Wireless, Wan, Traffic Statistics, System Up Time

Contents

Users Guide RW400SG Router OLITECPage 5.6.1 DHCP Settings Appendix C Specifications 5.11.3 Factory DefaultsAppendix A FAQ Appendix B Configuring the PCs 2.2 Features Chapter 2 Introduction2.1 Overview of the Router 2.3.1 The Front Panel 2.3 Panel Layout 2.3.2 The Rear Panel 3.1 System Requirements Chapter 3 Connecting the Router3.2 Installation Environment Requirements 3.3 Connecting the Router To WAN Switch/Hub（XDSL 、Cable 、Ethernet ） To LAN 4.1 TCP/IP configuration Chapter 4 Quick Installation Guide 4.2 Quick Installation Guide If you choose PPPoE, you will see this page shown in figure Figure 4-4 Login WindowsFigure 4-5 Quick Setup Figure 4-6 Choose WAN Connection Type Figure 4-7 Quick Setup - PPPoE In this page, you can configure the following wireless parameters Radio, SSID, Channel, Mode, Wireless MAC address and IP address Chapter 5 Configuring the Router5.1 login 2. Wireless Figure 5-1 Router Status 5.3 Quick Setup5.4 Network Please refer to Section 4.2 Quick Installation Guide 5.4.2 WAN 5.4.1 LAN Figure 5-4 WAN - Dynamic IP You should type the following parameters into the spaces provided Click Logout button to end 802.1x authenticationFigure 5-4a WAN - 802.1X + Dynamic IP Figure 5-5 WAN - Static IP Figure 5-6 WAN - PPPoE Click Login to start 802.1x authenticationClick Logout to end 802.1x authentication Figure 5-5a WAN - 802.1X + Static IP Figure 5-7 PPPoE Advanced Settings 5.4.3 MAC Clone 5.5.1 Wireless Settings 5.5 Wireless ¾ Mode - Select the desired wireless mode. The options are Encryptions 5.5.2 MAC Filtering Figure 5-12 Add or Modify Wireless MAC Address Filtering entry 5.5.3 Wireless Statistics 5.6 DHCP 5.6.1 DHCP Settings 5.6.2 DHCP Clients List To delete all Reserved IP addresses 5.6.3 Address ReservationTo Reserve IP addresses To modify A Reserved IP address 5.7.1 Virtual Servers 5.7 Forwarding To modify a virtual server entry To setup a virtual server entryTo delete a service entry To delete all service entries Figure 5-20 Port Triggering Once configured, operation is as follows 5.7.3 DMZ Modifying an existing ruleDeleting an existing rule To delete all rules 5.7.4 UPnP 5.8.1 Firewall 5.8 Security 5.8.2 IP Address Filtering 5.8.3 Domain Filtering To add or modify a Domain Filtering entry, follow these instructions Click the Enabled All button to make all entries enabledFigure 5-27 Domain Filtering Figure 5-28 Add or Modify a Domain Filtering entry 5.8.4 MAC Filtering 5.8.5 Remote Management 5.8.6 Advanced Security Click the Save button to save the settings 1. Modify the entry’s Destination IP Address, Subnet Mask and Gateway 5.9 Static RoutingTo add static routing entries To modify an existing entry 5.10.2 Oray.net DDNS 5.10 DDNSTo delete all the entries 5.10.1 Dyndns.org DDNS 5.10.3 Comexe.cn DDNS 5.11 System Tools 5.11.2 Firmware 5.11.1 Time 5.11.4 Reboot 5.11.3 Factory Defaults 5.11.5 Password 5.11.6 Log 5.11.7 StatisticsStatistics Table The total amount of packets received and transmitted by the router Click the Refresh button to refresh immediately 1. How do I configure the router to access Internet by ADSL users? Appendix A FAQ 3. I want to use Netmeeting, what do I need to do? 4. I want to build a WEB Server on the LAN, what should I do? 5. The wireless stations cannot connect to the router Appendix B Configuring the PCs 1. Install TCP/IP component2. Configure TCP/IP for your computer Assigned by DHCP Sever Setting IP address manually Figure B-6 DNS Configuration tabFigure B-5 Gateway tab Figure B-8 Gateway tab Figure B-7 IP Address tab click Add button. Shown below Figure B-9 DNS Configuration tab General Appendix C Specifications Appendix D Glossary ¾ Domain Name - A descriptive name for an address or group of addresses on the Internet