Manuals / Olitec / Computer Equipment / Network Router

Olitec RW400SG manual 4 WAN - Dynamic IP

Models: RW400SG

1 65

Download 65 pages 26.65 Kb

Page 18

Figure 5-4 WAN – Dynamic IP

Figure 5-4 WAN – Dynamic IP

This page displays the WAN IP parameters assigned dynamically by your ISP, including IP address, Subnet Mask, Default Gateway, etc. Click the Renew button to renew the IP parameters from your ISP. Click the Release button to release the IP parameters.

MTU Size: The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. For some ISPs you need to reduce the MTU. But this is rarely required, and should not be done unless you are sure it is necessary for your ISP connection.

If your ISP gives you one or two DNS addresses, select Use These DNS Servers and enter the primary and secondary addresses into the correct fields. Otherwise, the DNS servers will be assigned dynamically from ISP.

Note: If you get ‘Address not found' errors when you go to a Web site, it is likely that your DNS servers are set up improperly. You should contact your ISP to get DNS server addresses.

Get IP with Unicast DHCP: A few ISPs' DHCP servers do not support the broadcast applications. If you cannot get the IP Address normally, you can choose this option. (You generally need not check this option).

If you are also given a user name and a password for 802.1x authentication, you should select 802.1x + Dynamic IP for WAN Connection Type, and a user name and a password will then appear, shown in figure 5-4a:

- 14 -

Image 18

Olitec RW400SG manual 4 WAN - Dynamic IP

Contents

RW400SG Router OLITEC Users GuidePage 5.6.1 DHCP Settings Appendix B Configuring the PCs 5.11.3 Factory DefaultsAppendix A FAQ Appendix C Specifications2.2 Features Chapter 2 Introduction2.1 Overview of the Router 2.3 Panel Layout 2.3.1 The Front Panel2.3.2 The Rear Panel 3.3 Connecting the Router Chapter 3 Connecting the Router3.2 Installation Environment Requirements 3.1 System Requirements（XDSL 、Cable 、Ethernet ） Switch/HubRESET To LANChapter 4 Quick Installation Guide 4.1 TCP/IP configuration4.2 Quick Installation Guide Figure 4-6 Choose WAN Connection Type Figure 4-4 Login WindowsFigure 4-5 Quick Setup If you choose PPPoE, you will see this page shown in figureFigure 4-7 Quick Setup - PPPoE In this page, you can configure the following wireless parameters 2. Wireless Chapter 5 Configuring the Router5.1 login Radio, SSID, Channel, Mode, Wireless MAC address and IP addressPlease refer to Section 4.2 Quick Installation Guide 5.3 Quick Setup5.4 Network Figure 5-1 Router Status5.4.1 LAN 5.4.2 WANFigure 5-4 WAN - Dynamic IP Figure 5-5 WAN - Static IP Click Logout button to end 802.1x authenticationFigure 5-4a WAN - 802.1X + Dynamic IP You should type the following parameters into the spaces providedFigure 5-5a WAN - 802.1X + Static IP Click Login to start 802.1x authenticationClick Logout to end 802.1x authentication Figure 5-6 WAN - PPPoEFigure 5-7 PPPoE Advanced Settings 5.4.3 MAC Clone 5.5 Wireless 5.5.1 Wireless Settings¾ Mode - Select the desired wireless mode. The options are Encryptions 5.5.2 MAC Filtering Figure 5-12 Add or Modify Wireless MAC Address Filtering entry 5.5.3 Wireless Statistics 5.6.1 DHCP Settings 5.6 DHCP5.6.2 DHCP Clients List To modify A Reserved IP address 5.6.3 Address ReservationTo Reserve IP addresses To delete all Reserved IP addresses5.7 Forwarding 5.7.1 Virtual ServersTo delete all service entries To setup a virtual server entryTo delete a service entry To modify a virtual server entryFigure 5-20 Port Triggering Once configured, operation is as follows To delete all rules Modifying an existing ruleDeleting an existing rule 5.7.3 DMZ5.7.4 UPnP 5.8 Security 5.8.1 Firewall5.8.2 IP Address Filtering 5.8.3 Domain Filtering Figure 5-27 Domain Filtering Click the Enabled All button to make all entries enabledClick the Disabled All button to make all entries disabled Figure 5-28 Add or Modify a Domain Filtering entry5.8.4 MAC Filtering 5.8.5 Remote Management 5.8.6 Advanced Security Click the Save button to save the settings To modify an existing entry 5.9 Static RoutingTo add static routing entries 1. Modify the entry’s Destination IP Address, Subnet Mask and Gateway5.10.1 Dyndns.org DDNS 5.10 DDNSTo delete all the entries 5.10.2 Oray.net DDNS5.10.3 Comexe.cn DDNS 5.11 System Tools 5.11.1 Time 5.11.2 Firmware5.11.3 Factory Defaults 5.11.4 Reboot5.11.5 Password 5.11.6 Log 5.11.7 StatisticsStatistics Table Click the Refresh button to refresh immediately The total amount of packets received and transmitted by the routerAppendix A FAQ 1. How do I configure the router to access Internet by ADSL users?3. I want to use Netmeeting, what do I need to do? 4. I want to build a WEB Server on the LAN, what should I do? 5. The wireless stations cannot connect to the router Appendix B Configuring the PCs 1. Install TCP/IP component2. Configure TCP/IP for your computer Assigned by DHCP Sever Setting IP address manually Figure B-6 DNS Configuration tabFigure B-5 Gateway tab Figure B-7 IP Address tab Figure B-8 Gateway tabclick Add button. Shown below Figure B-9 DNS Configuration tab Appendix C Specifications GeneralAppendix D Glossary ¾ Domain Name - A descriptive name for an address or group of addresses on the Internet