Manuals / Omega / Lawn and Garden / Weather Radio

Omega CNI8DV, CNI16D, CNI8C, CNI8DH, CNI32 manual Set Points, Setpoint

Models: CNI16 CNI32 CNI8DH CNI8C CNI16D CNI8 CNI8DV

1 72

Download 72 pages 49.28 Kb

Page 21

3.2.2 Set Points

SETPOINT 1:

Press a 1) Press a, if necessary until SP1 prompt appears. Press d 2) Display shows previous value of “Setpoint 1”. Press b & c 3) Press b and c to increase or decrease Setpoint 1

respectively.

Holding b & c buttons down for approximately 3 seconds will speed up the rate at which the Setpoint value increments or decrements.

Press b & c 4) Continue to use b and c to enter your 4-digit Setpoint 1 value. Press d 5) Display shows STRD stored message momentarily and then

advances to SP2 only, if a change was made, otherwise press a to advance to SP2 Setpoint 2 Menu.

SETPOINT 2:

Press d 6) Display shows previous value of “Setpoint 2”. Press b & c 7) Press b and c to increase or decrease Setpoint 2

respectively.

Holding b & c buttons down for approximately 3 seconds will speed up the rate at which the setpoint value increments or decrements.

Press d 8) Display shows STRD stored message momentarily and then advances to CNFG only, if a change was made, otherwise press a to advance to CNFG Configuration Menu.

17

Image 21

Omega CNI8DV, CNI16D, CNI8C, CNI8DH, CNI32 manual Set Points, Setpoint

Contents

Temperature & Process Controller Manual CNi8, CNi8C, CNi8DH, CNi8DV, CNi16, CNi16D, CNi32User’s Guide Shop on line atServicing North America OMEGAnet On-Line ServiceFor immediate technical or application assistance Servicing EuropePart 2 Setup TABLE OF CONTENTSElectrical Installation Process Current - Wiring HookupLIST OF TABLES LIST OF FIGURESTwo/Three/Four-wire RTD Process Current Wiring HookupWARNING or CAUTION NOTES, WARNINGS and CAUTIONSPART INTRODUCTION 1.1 Description 1.2 Safety Considerations EMC ConsiderationsFailure to follow all instructions and warnings may result in injury To Disable Outputs Customer ServiceTo Reset the Meter 1.3 Before You BeginFigure 2.1 Front Panel Display Table 2.1 Front Panel Annunciators PART SETUP 2.1 Front PanelPOWER Figure 2.2 Rear Panel Power and Output Connections2.2 Rear Panel Connections INPUT2.3 Electrical Installation 2.3.1 Power Connections Figure 2.4 Main Power ConnectionsTable 2.3 Fuse Requirement see specifications 2.3.2 Thermocouple Figure 2.5 Thermocouple Wiring Hookup Table 2.4 TC Wire Color ChartInput Connector TYPE500 ohm Wiring Hookup 2.3.3 Two/Three/Four-Wire RTDFigure 2.6 a RTD-1000 ohm and b RTD-100 ohm Wiring Hookupa Process Voltage Wiring Hookup b Process Voltage Wiring Hookup Figure 2.7 Process Current Wiring Hookup2.3.4 Process Current Internal and External ExcitationOutputs Wiring Hookup 2.3.6 Wiring Outputsa Mechanical Relay and SSR b Pulse and Analoga RS-232 Output Wiring Hookup b RS-485 Output Wiring Hookup Snubber Circuits Wiring HookupFigure 2.12 Excitation Output i/8DH Dual Horizontal i/8DV Dual Vertical 2.3.7 Dual Display Color SetupFigure 2.14 i/8D Location of S1 and Selectable Jumper Positions Figure 2.15 i/16D Location of S1 and Selectable Jumper PositionsPART OPERATION Configuration Mode 3.1 Introduction Table 3.1 Button Function in Configuration ModeTurning your Controller On for the First Time Figure 3.1 Flow Chart for ID and Setpoints 3.2 Menu ConfigurationENTERING YOUR NON-DEFAULT FULL SECURITY ID NUMBER ENTERING YOUR NON-DEFAULT SETPOINT/ID SECURITY ID NUMBER3.2.1 ID Number 3.2.2 Set Points SETPOINTSETPOINT 3.2.3 Configuration Menu Figure 3.2 Flow Chart for Configuration Menu 3.2.4 Input Type Menu Figure 3.3 Flow Chart for Input Type MenuEnter Configuration Menu ENTER INPUT TYPE MENU Input Type ThermocoupleTHERMOCOUPLE SUBMENU Thermocouple TypesRTD SUBMENU Input Type RTDRTD Types RTD VALUE SUBMENUFigure 3.4 Flow Chart for Reading Configuration Menu 3.2.5 Reading ConfigurationInput Type Process PROCESS SUBMENUTEMPERATURE UNIT SUBMENU ENTER READING CONFIGURATION MENUDECIMAL POINT SUBMENU FILTER CONSTANT SUBMENUINPUT/READING SCALE AND OFFSET SUBMENU Reading Configuration If Process was selectedTable 3.2 Conversion Table RANGECONVERSION NUMBER 3.2.6 Alarm Figure 3.5 Flow Chart for AlarmENTER ALARM 1 MENU ALARM 1 ENABLE/DISABLE SUBMENU ALARM 1 ABSOLUTE/DEVIATION SUBMENUALARM 1 LATCH/UNLATCH SUBMENU ACTIVE SUBMENU CONTACT CLOSURE SUBMENUALARM ENABLE/DISABLE AT POWER ON ALARM 1 LOW VALUE SUBMENUALARM 1 HI VALUE SUBMENU Figure 3.6 Flow Chart for Analog Output Retransmission 3.2.7 Analog Output RetransmissionENTER ANALOG OUTPUT MENU CURRENT/VOLTAGE SUBMENU ANALOG OUTPUT ENABLE/DISABLE SUBMENUREADING READINGFor example Figure 3.7 Flow Chart for Alarm 3.2.8 AlarmENTER ALARM 2 MENU ALARM 2 ENABLE/DISABLE SUBMENULOOP BREAK ENABLE/DISABLE SUBMENU Figure 3.8 Flow Chart for Loop Break Time/Field CalibrationREADING ADJUST SUBMENU 3.2.9 Loop Break Time/Field CalibrationSETPOINT DEVIATION ENABLE/DISABLE SUBMENU 3.2.9 Loop Break Time/Field Calibration continuedTHERMOCOUPLE FIELD CALIBRATION SUBMENU 3.2.10 Output Figure 3.9 Flow Chart for OutputENTER OUTPUT 1 MENU SELF SUBMENUMINIMUM/PERCENT LOW SUBMENU CONTROL TYPE OUTPUT MAXIMUM/PERCENT HIGH SUBMENUACTION TYPE SUBMENU AUTO PID SUBMENUANTI INTEGRAL SUBMENU PROPORTIONAL BAND SUBMENU START AUTO TUNE PIDRESET SETUP SUBMENU RATE SETUP SUBMENUCYCLE TIME SUBMENU DEADBAND SUBMENU DAMPING FACTOR SUBMENU3.2.11 Output Figure 3.10 Flow Chart for OutputENTER OUTPUT 2 MENU CONTROL TYPE SUBMENUACTION TYPE SUBMENU AUTO PID SUBMENUPROPORTIONAL BAND SUBMENU DEADBAND SUBMENU CYCLE TIME SUBMENURAMP ENABLE/DISABLE SUBMENU Figure 3.11 Flow Chart for Ramp and Soak3.2.12 Ramp & Soak ENTER RAMP AND SOAK MENUSOAK ENABLE/DISABLE SUBMENU RAMP VALUE SUBMENUSOAK VALUE SUBMENU 3.2.13 ID CODE Figure 3.12 Flow Chart for ID Code ENTERING OR CHANGING YOUR NON-DEFAULT ID CODEENTER ID CODE MENU ENTERING OR CHANGING YOUR DEFAULT ID CODE FULL SECURITY LEVEL SUBMENUSETPOINT/ID SECURITY LEVEL SUBMENU 3.2.14 COMMUNICATION OPTION Figure 3.13 Flow Chart for Communication OptionCOMMUNICATION PARAMETERS SUBMENU ENTER COMMUNICATION OPTION MENUBAUD SUBMENU PARITY SUBMENUBUS FORMAT SUBMENU STOP BIT SUBMENUMODBUS PROTOCOL SUBMENU LINE FEED SUBMENUCOMMUNICATION INTERFACE STANDARD SUBMENU DATA FLOW MODE SUBMENUDATA SEPARATION CHARACTER SUBMENU 33 Display shows STRD stored message momentarily and thenDATA FORMAT SUBMENU ALARM STATUS SUBMENUMAIN READING SUBMENU PEAK VALUE SUBMENUADDRESS VALUE SUBMENU ADDRESS SETUP SUBMENUTRANSMIT TIME INTERVAL SUBMENU TRANSMIT TIME INTERVAL VALUE SUBMENUALARM 1 DISPLAY COLOR SUBMENU Figure 3.14 Flow Chart for Display Color Selection3.2.15 DISPLAY COLOR SELECTION ENTER DISPLAY COLOR SELECTION MENUExample ALARM 2 DISPLAY COLOR SUBMENUDisplay Colors change sequences GREENExample Display colors change sequencesDisplay Colors change sequences GREENResolution PART SPECIFICATIONSTemperature Stability ConfigurationALARM 1 & 2 programmable Type ResetModes RateGENERAL Line Voltage/Power INSULATION Power to Input/Output 2300 Vac per 1 min. testLow Voltage/Power Option External Fuse Required Time-Delay, UL 248-14 listedInput Type Table 4.1 Input PropertiesRange AccuracyFACTORY PRESET VALUES PART FACTORY PRESET VALUES Table 5.1 Factory preset valueReading Configuration RDG Alarm 1MENU ITEMS FACTORY PRESET VALUES NOTESRamp & Soak RAMP Communication ParametersElectrical Safety EN61010-12001 PART CE APPROVALS INFORMATIONNote *Units configured for external low power dc voltage, 12-36Vdc Double InsulationPage Page RETURN REQUESTS/INQUIRIES WARRANTY/DISCLAIMEROMEGA…Of Course TEMPERATUREPRESSURE, STRAIN AND FORCE FLOW/LEVEL