Video

Video

There’s no picture

Make sure that all video connecting plugs are pushed

14

in all the way.

 

 

 

Make sure that each video component is properly

15, 16,

connected.

56

If your TV is connected to the HDMI OUT, select

37

- - - - - in the “HDMI Input” setup to watch com-

 

posite video, and component video sources.

 

 

 

If the video source is connected to a component

16, 37

video input, you must assign that input to an input

 

selector, and your TV must be connected to either

 

the HDMI OUT or COMPONENT VIDEO MONI-

 

TOR OUT.

 

If the video source is connected to a composite video

16

input, your TV must be connected to the HDMI

 

OUT or the corresponding composite video output.

 

 

 

If the video source is connected to an HDMI input,

15, 37

you must assign that input to an input selector, and

 

your TV must be connected to the HDMI OUT.

 

On your TV, make sure that the video input to which

the AV receiver is connected is selected.

 

There’s no picture from a source connected to an HDMI IN

Reliable operation with an HDMI-to-DVI adapter is 71 not guaranteed. In addition, video signals from a PC are not guaranteed.

When the Resolution is set to any resolution not sup- 37 ported by the TV, no video is output by the HDMI outputs.

If the message Resolution Error appears on the AV — receiver’s display, this indicates that your TV does

not support the current video resolution and you need to select another resolution on your DVD player.

The on-screen menus don’t appear

(European models) Specify the TV system used in 48 your area in the “TV Format”.

On your TV, make sure that the video input to which — the AV receiver is connected is selected.

When the AV receiver doesn’t connect TV with

HDMI, onscreen menus are not displayed.

 

The picture is distorted

(European models) Specify the TV system used in 48 your area in the “TV Format”.

The on screen display does not appear

Depending on the input signal, the on screen display 48 may not appear when the input signal from the

HDMI IN is output to a device connected to the

HDMI OUT.

En

Tuner

Reception is noisy, FM stereo reception is noisy, or the FM STEREO indicator doesn’t light

Relocate your antenna.

Move the AV receiver away from your TV or com-

puter.

 

Listen to the station in mono.

26

 

 

When listening to an AM station, operating the

remote controller may cause noise.

 

Passing cars and airplanes can cause interference.

 

 

Concrete walls weaken radio signals.

 

 

If nothing improves the reception, install an outdoor — antenna.

Remote Controller

The remote controller doesn’t work

Before operating this unit, be sure to press

RECEIVER.

 

 

 

Make sure that the batteries are installed with the

4

correct polarity.

 

Install new batteries. Don’t mix different types of

4

batteries, or old and new batteries.

 

 

 

Make sure that the remote controller is not too far

4

away from the AV receiver, and that there’s no

 

obstruction between the remote controller and the

 

AV receiver’s remote control sensor.

 

Make sure that the AV receiver is not subjected to

direct sunshine or inverter-type fluorescent lights.

 

Relocate if necessary.

 

 

 

If the AV receiver is installed in a rack or cabinet

with colored-glass doors, the remote controller may

 

not work reliably when the doors are closed.

 

Make sure you’ve selected the correct remote con-

9, 62

troller mode.

 

 

 

When using the remote controller to control other

manufacturers’ AV components, some buttons may

 

not work as expected.

 

Make sure you’ve entered the correct remote control

61

code.

 

 

 

Make sure to set the same ID on both the AV receiver

49

and remote controller.

 

 

 

Can’t control other components

If it’s an Onkyo component, make sure that the u

17

cable and analog audio cable are connected properly.

 

Connecting only an ucable won’t work.

 

 

 

Make sure you’ve selected the correct remote con-

9, 62

troller mode.

 

If you’ve connected a cassette tape deck, to the TV/

23

CD IN jack, or an RI Dock to the TV/CD IN or

 

GAME IN or VCR/DVR IN jacks, for the remote

 

controller to work properly, you must set the display.

 

 

 

If you cannot operate it, you will need to enter the

60

appropriate remote control code.

 

To control another manufacturer’s component, point

61

the remote controller at that component.

 

 

 

To control an Onkyo component that’s connected via

61

u, point the remote controller at the AV receiver.

 

Be sure to enter the appropriate remote control code

 

first.

 

 

 

66

Page 66
Image 66
Onkyo HT-R980 Video, Tuner, Remote Controller, There’s no picture, The on-screenmenus don’t appear, troller mode, first