Onkyo HT-RC460 instruction manual En-75, Video, Tuner, Remote Controller

Video

■ There’s no picture

Make sure that all video connecting plugs are pushed	14
in all the way.
Make sure that each video component is properly	15, 16
connected.
If your TV is connected to the HDMI output(s), select	48
“- - - - -” in the “HDMI Input” setup to watch
composite video, and component video sources.
If the video source is connected to a component video	16, 49
input, you must assign that input to an input selector,
and your TV must be connected to either the HDMI
output(s) or COMPONENT VIDEO OUT.
If the video source is connected to a composite video	16
input, your TV must be connected to the HDMI
output(s) or the corresponding composite video
output.
If the video source is connected to an HDMI input,	15, 48
you must assign that input to an input selector, and
your TV must be connected to the HDMI output(s).
On your TV, make sure that the video input to which	—
the AV receiver is connected is selected.

■There’s no picture from a source connected to an HDMI IN

Reliable operation with an HDMI-to-DVI adapter is	88
not guaranteed. In addition, video signals from a PC
are not guaranteed.
When the resolution is set to any resolution not	48
supported by the TV, no video is output from the
HDMI outputs.
If the message “Resolution Error” appears on the	—
AV receiver’s display, this indicates that your TV

does not support the current video resolution and you need to select another resolution on your DVD player.

■The on-screen menus don’t appear

On your TV, make sure that the video input to which — the AV receiver is connected is selected.

When the AV receiver is not connected to a TV via — HDMI OUT MAIN, on-screen menus are not displayed.

■The on-screen display does not appear

Depending on the input signal, the on-screen display 43 may not appear when the input signal from HDMI IN

is output to a device connected to HDMI OUT MAIN.

Tuner

■Reception is noisy, FM stereo reception is noisy, or the FM STEREO indicator doesn’t light

Relocate your antenna.	—
Move the AV receiver away from your TV or	—
computer.
Listen to the station in mono.	30
When listening to an AM station, operating the	—
remote controller may cause noise.
Passing cars and airplanes can cause interference.	—
Concrete walls weaken radio signals.	—
If nothing improves the reception, install an outdoor	—
antenna.

Remote Controller

■The remote controller doesn’t work

Before operating this unit, be sure to press	—
RECEIVER.
Make sure that the batteries are installed with the	4
correct polarity.
Install new batteries. Don’t mix different types of	4
batteries, or old and new batteries.
Make sure that the remote controller is not too far	4
away from the AV receiver, and that there’s no
obstruction between the remote controller and the AV
receiver’s remote control sensor.
Make sure that the AV receiver is not subjected to	—
direct sunshine or inverter-type fluorescent lights.
Relocate if necessary.

En-75

	Appendix
	If the AV receiver is installed in a rack or cabinet	—
	with colored-glass doors, the remote controller may
	not work reliably when the doors are closed.
	Make sure you’ve selected the correct remote	10, 70
	controller mode.
	When using the remote controller to control other	—
	manufacturers’ AV components, some buttons may
	not work as expected.
	Make sure you’ve entered the correct remote control	69
	code.
	Make sure to set the same ID on both the AV receiver	63
	and remote controller.
■ Can’t control other components
	If it’s an Onkyo component, make sure that the u	17
	cable and analog audio cable are connected properly.
	Connecting only an ucable won’t be enough.
	Make sure you’ve selected the correct remote	10, 70
	controller mode.
	If you’ve connected an cassette tape deck to the	41
	TV/CD IN jack, or an RI Dock to the TV/CD IN or
	GAME IN jacks, for the remote controller to work
	properly, you must set the input display
	appropriately.
	If you cannot operate it, you will need to enter the	68
	appropriate remote control code.
	To control another manufacturer’s component, point	69
	the remote controller at that component.
	To control an Onkyo component that’s connected via	70
	u, point the remote controller at the AV receiver.
	Be sure to enter the appropriate remote control code
	first.
	To control an Onkyo component that’s not connected	70
	via u, point the remote controller at the component.
	Be sure to enter the appropriate remote control code
	first.
	The entered remote control code may not be correct.	—
	If more than one code is listed, try each one.