Onkyo TX-NR5009 Front, Center*1, Surround*1, Surround Back*2*3*4*5, Surround Back Ch, Double Bass

Speaker Configuration

This setting is set automatically by

Audyssey MultEQ® XT32 Room Correction and Speaker Setup function (➔ page 33). For Speakers B, you need to change the settings manually.

With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. You can set the crossover frequencies, distances, and levels of the front speakers A and front speakers B independently. The other speakers (i.e., subwoofer, center, surround, surround back and front high) use the same crossover frequencies, distances, and levels for Speakers A and Speakers B. Specify “Full Band” for speakers that can output low frequency bass sounds adequately, for example, speakers with a good sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover frequency will be output by the subwoofer instead of the speaker. Refer to your speaker’s manuals to determine the optimum crossover frequencies. If you set up your speakers using Audyssey MultEQ XT32 Room Correction and Speaker Setup, please make sure manually that any THX speakers are set to “80Hz(THX)” crossover.

■Subwoofer

`1ch:

Audio signal is outputted from SW1 jack only.

`2ch:

Audio signal is outputted from SW1 and SW2 jacks.

`No

■Front

(Setting Speakers A and Speakers B)

`Full Band

`40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX), 90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz

Note

•If the “Subwoofer” setting is set to “No”, the “Front” (Speakers B) setting is fixed to “Full Band”.

•If any of “Center”, “Surround”, or “Front High” is set to “Full Band”, the “Front” (Speakers B) setting is fixed to “Full Band”.

■Center*1, Surround*1, Surround Back*2*3*4*5

`Full Band

`40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX), 90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz

`None

■Front Wide*2*6*7*8, Front High*1*2*7

`Full Band

`40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX), 90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz

`None

Note

*1 “Full Band” can be selected only when “Full Band” is selected in the “Front”(Speakers A) setting.

*2 If the “Surround” setting is set to “None”, this setting cannot be selected.

*3 If the “Surround” setting is set to anything other than “Full Band”, “Full Band” cannot be selected here.

*4 When the “Powered Zone 3” setting is set to “Yes”, this setting cannot be used.

*5 When “Front High + Front Wide” is set to “Yes”, this setting cannot be selected.

*6 “Full Band” can be selected only when “Full Band” is selected in the “Front” setting.

*7 If “Bi-Amp” is selected, or the “Powered Zone 2” setting is set to “Yes”, this setting cannot be selected.

*8 If anything other than “No” is selected in “Speakers Type(Front B)”, this setting cannot be selected.

■Surround Back Ch

`1ch:

Select if only one surround back speaker L is connected.

`2ch:

Select if two (left and right) surround back speakers are connected.

Note

•If the “Surround Back” setting is set to “None”, this setting cannot be selected.

■LPF of LFE

(Low-Pass Filter for the LFE Channel)

`80Hz, 90Hz, 100Hz, 110Hz, 120Hz

`Bypass:

Low-Pass Filter is not applied.

With this setting, you can specify the cutoff frequency of the LFE channel’s low-pass filter (LPF), which can be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel.

Note

• If you’re using THX-certified speakers, select “80Hz”.

■Double Bass

This setting is NOT set automatically by

Audyssey MultEQ XT32 Room Correction and Speaker Setup function (➔ page 33).

`On

`Off(THX)

Turn this setting on to boost bass output by feeding bass sounds from the front left, right, and center channels to the subwoofer.

Note

•This function can be set only if the “Subwoofer” setting is set to “1ch” or “2ch”, or the “Front” setting is set to “Full Band”.

•If you’re using THX-certified speakers, select “Off(THX)”.

En

52