Onkyo TX-SR502E instruction manual Controlling Other Components, Entering Remote Control Codes

TX-SR502_En.book Page 50 Tuesday, February 17, 2004 12:14 PM

Controlling Other Components

You can use the TX-SR502/TX-SR502E’s remote con- troller (RC-567M/RC-569M) to control your other AV components, including those made by other manufactur- ers. To do this you first need to enter the appropriate remote control code for your DVD player, TV, VCR, cable receiver, or satellite receiver. Then you need to select the corresponding remote controller mode (see page 10).

By entering the appropriate remote control code, the [CD], [MD], and [CDR] mode buttons can also be used with other manufacturer’s components (e.g., DVD, TV, VCR, satellite or cable receiver).

4 Select the remote controller mode, point the remote controller at the component, and check its operation.

Remote controller buttons that can be used in DVD mode are shown on page 12. Those that can be used with the TV, VCR, CABLE, and SAT modes are shown on page 55.

If the remote controller works as expected, the code has been entered correctly. If not, try again or try another code.

ON	STANDBY							TV	TV I
					I			INPUT	STANDBY
V1	V2				V3
1		2			3			+
DVD	MULTI CH							TV CH
4		5			6			-	Number
CD	TAPE				TUNER
7		8			9
									buttons
								TV VOL
+10		0			CLEAR
--/---								TUNER/
TONE		_						TAPE
					+			AMP
	REMOTE MODE
DVD	CD				MD			CDR	DVD, CD, MD,
TV	VCR				CABLE			SAT	CDR, TV, VCR,
DIMMER								SLEEP	CABLE, SAT
TV			NU		ME
	ME					N
	P
INPUT	O						U
	T
+
CH
DISC				ENTER				VOL
-		EX
					E
	R			IT	GU
PREV							P
	ET	U				U
CH			RN		S
DISPLAY								MUTING

Entering Remote Control Codes

Entering the appropriate remote control code for your TV, VCR, and so on will allow you to control it with the TX-SR502/TX-SR502E’s remote controller. You’ll need to perform this procedure for each component that you want to control.

1 Look up the remote control code for your component.

See “Remote Control Codes” on page 51.

2	While holding down the [DVD], [TV],
	[VCR], [CABLE], [SAT], [CD], [MD], or
	[CDR] mode button, press the [STANDBY]
	button.
3	Within 30 seconds, use the number but-
	tons to enter the 4-digit remote control

code.

Codes for Onkyo DVD Players

The remote control code for an Onkyo DVD player

depends on whether it’s connected via , as follows:

5001: Use this code if you’ve connected an cable and an analog audio cable (RCA) to your DVD player. This is the default setting, so if you’re

using , you don’t need to change anything. Point the remote controller at the TX-SR502/ TX-SR502E to operate the DVD player.

5002: Use this code if your DVD player doesn’t have

an socket, or you’re not using . Point the remote controller at the DVD player to operate it.

Resetting the [DVD], [CD], [MD] or [CDR] Mode Button

By default, the [DVD], [CD], [MD] & [CDR] mode but- tons are preprogrammed with remote control codes for

controlling Onkyo components connected via . If you’ve entered another code for a button and now want to return to its default, perform the following procedure.

1 While holding down the mode button that you want to reset, press the TV [ ] but- ton.

Release both buttons and wait two seconds.

2 Press the mode button again.

The mode button is reset.

Resetting the Remote Controller

This section explains how to reset the remote controller to its default settings.

1 While holding down the [AMP] mode but- ton, press the [STANDBY] button.

Release both buttons and wait five seconds.

2 Press the [AMP] mode button again.

The remote controller is reset.

50