Onkyo TX-SR701E, TX-SR601E Connecting a television monitor or projector Monitor OUT

Connections

8. TV monitor or projector

(MONITOR OUT)

			ANTENNA	AM
	COMPONENT VIDEO
7. DVD recorder, other	INPUT 2	INPUT 1	OUTPUT
			Y
digital video recording
device (VIDEO 2)			PB

FM 75

ZONE 2

LINE OUT

L

Component

Digital audio			PR
			COAXIAL IN
input (coaxial)	IN	OUT
	DIGITAL		VIDEO 3
	OPTICAL	OPTICAL
	2	1
TX-SR701/701E only
Video input			IN
			COAXIAL

VIDEO 2

OUT IN

RREMOTE CONTRO

VIDEO 1		DVD	MONITOR	ZON
OUT	IN	IN	OUT
				V
				S

video input

Video input

S Video input
	L (white)
Analog audio
input	R (red)
	L (white)
Analog audio
output	R (red)

IN

GND

L

R

PHONO

IN

CD

OUT IN IN

TAPE VIDEO 3

OUT IN

VIDEO 2

OUT	IN	FRONT SURR CENTER
		L
		R
VIDEO 1		SUB
		WOOFER

DVD

S Video input

S Video output

Video output

: Signal flow

7.Connecting a DVD recorder or other digital video recording device (VIDEO 2)

Using RCA video cables, connect the video output jack (composite) of the device to the VIDEO 2 V IN jack of the TX-SR701/701E/ 601/601E and connect the video input jack of the device to the VIDEO 2 V OUT jack of the TX-SR701/701E/601/601E. Or if the device has S video input and output jacks, using S video cables, connect the S video output jack of the device to the VIDEO 2 S IN jack of the TX-SR701/701E/601/601E and connect the video input jack of the device to the VIDEO 2 S OUT jack of the TX-SR701/ 701E/601/601E. Or if the device has component video outputs, connect them to the COMPONENT VIDEO INPUT 1 or 2 jacks on the TX-SR701/701E/601/601E.

With the initial settings of the TX-SR701/701E/601/601E, the VIDEO 2 input source is set for the COMPONENT VIDEO INPUT 2 jacks.

If you connect the device to the COMPONENT VIDEO INPUT 1 jacks, this must be changed at “Input Setup” → “Component Video” (see page 53).

Using RCA audio cables, connect the audio output jacks of the device to the VIDEO 2 IN audio jacks of the TX-SR701/701E/601/ 601E and connect the audio input jacks of the device to the VIDEO 2 OUT audio jacks of the TX-SR701/701E/601/601E. Make sure that you properly connect the left channels to the L jacks and the right channels to the R jacks.

If the device has a digital output, connect it to either the DIGITAL IN COAXIAL jack or the DIGITAL IN OPTICAL jack of the TX- SR701/701E/601/601E depending on the type of connector on the device.

With the initial settings of the TX-SR701/701E/601/601E, nothing is allocated as the digital input source for VIDEO 2 (----).

If you connect the digital audio output, be sure to make the appropriate changes at “Input Setup” → “Digital Input” (see page 52).

If the device has a digital input, connect it to the DIGITAL OUTPUT jack of the TX-SR701/701E/601/601E for digital recording of the signal from the digital input of the TX-SR701/ 701E/601/601E.

Note:

The output from the DIGITAL OUT jack of the TX-SR701/701E/ 601/601E is only the digital signal input to the DIGITAL IN jack.

8.Connecting a television monitor or projector (MONITOR OUT)

The TX-SR701/701E/601/601E is equipped with a simple Y/C separate circuit and simple Y/C mixed circuit. Since both the signal from the S and V inputs are output to the MONITOR OUT S output, if the television or projector is equipped with an S video input, it is unnecessary to connect the video connectors. If it is equipped with only a video input, connect it to the MONITOR OUT V output.

Using an RCA video cable, connect the video input jack (composite) of the device to the MONITOR OUT V jack of the TX- SR701/701E/601/601E. Or if the device has an S video input jack, connect it to the MONITOR OUT S jack of the TX-SR701/701E/ 601/601E using an S video cable. Or if the device has component video inputs, connect them to the bank of COMPONENT VIDEO OUTPUT jacks on the TX-SR701/701E/601/601E.

Note:

Note that the Setup Menu will only be displayed on the monitor connected to MONITOR OUT (S or V) and not those connected to the COMPONENT VIDEO OUTPUT jacks.

20