Configuring the speakers
4.Use the 
and 
cursor buttons to select “Subwoofer” and then use the 
and 
cursor buttons to select the subwoofer setting.
Yes: Select when a subwoofer is connected.
No: Select when a subwoofer is not connected.
Remote controller | |
TUNING |
|
PRESET |
|
TUNING
PRESET
5.Use the 
and 
cursor buttons to select “Front L/R” and then use the 
and 
cursor buttons to select the front speaker setting.
Large: Select if the front speakers are large sized.
Small: Select if the front speakers are small sized.
•If “No” is selected for the Subwoofer setting, this setting is fixed to “Large.”
6.Use the 
and 
cursor buttons to select “Center” and then use the 
and 
cursor buttons to select the center speaker setting.
None: Select if no center speaker is connected.
Large: Select if the center speaker is large sized.
Small: Select if the center speaker is small sized.
•If “Small” is selected for the Front setting, “Large” cannot be selected for this setting.
7.Use the 
and 
cursor buttons to select “Surround L/ R” and then use the 
and 
cursor buttons to select the surround speaker setting.
None: Select if no surround left and right speakers are connected.
Large: Select if the surround left and right speakers are large sized.
Small: Select if the surround left and right speakers are small sized.
•If “Small” is selected for the Front setting, “Large” cannot be selected for this setting.
8.Use the 
and 
cursor buttons to select “Surround back” and then use the 
and 
cursor buttons to select the surround back speaker setting.
None: Select if no surround back speaker is connected.
Large: Select if the surround back speaker is large sized.
Small: Select if the surround back speaker is small sized.
•If “None” is selected for the Surround setting, this setting will be disabled.
•If “Small” is selected for the Surround setting, “Large” cannot be selected for this setting.
9.Use the 
and 
cursor buttons to select “Crossover” and then use the 
and 
cursor buttons to select the crossover frequency mode setting.
Adjustable Crossover for Bass Management
TX-SR701/701E
f. Crossover
This setting allows you to set the crossover frequency for your speaker system. The crossover frequency is the minimum frequency delivered to a speaker and can be set to 40 Hz, 60 Hz, 80 Hz (THX), 100 Hz, 120 Hz, or 150Hz. Select “80Hz (THX)” if you are using a
Note:
When “Large” is set, the complete frequency range for that speaker channel will be output. When “Small” is set, the frequencies below 80 Hz for that speaker channel are output to the subwoofer. If Subwoofer is set to “No” in the Speaker Config menu, then they will be output to the left and right front speakers. (Set all speakers for THX speaker systems to “small.”)
TX-SR601/601E
f. Crossover
This setting allows you to set the crossover frequency for your speaker system. The crossover frequency is the minimum frequency delivered to a speaker and can be set to 60 Hz, 80 Hz, 100 Hz, 120 Hz, or 150Hz. This setting is valid when “Subwoofer” is set to “Yes,” or for speakers that are set to “Small,” at the “Speaker Config” menu. Frequencies below this are cut from speakers set to “Small” and sent to the subwoofer (or to speakers set to “Large”).
The following table lists the crossover frequency you should choose depending on the diameter of your front spekers.
Front speaker diameter | crosscover frequency |
|
|
Larger than 12" (30cm) | 40 |
|
|
8"~12" | 60 |
|
|
80 | |
|
|
100 | |
|
|
120 | |
|
|
Less than | 150 |
|
|
Note:
When “Large” is set, the complete frequency range for that speaker channel will be output. When “Small” is set, the frequencies below 80 Hz for that speaker channel are output to the subwoofer. If Subwoofer is set to “No” in the
Press the RETURN button to return to the main menu.
Press the SETUP button on the front panel or on the remote controller to exit the Setup menu.
32
