Orion 2000 guide

Installing the Software Drivers in Windows 2000 Operating System

To install the cable modem software drivers using the Windows 2000 operating system:

1.Power on your PC. After your computer boots, Windows detects the cable modem. The Found New Hardware screen appears, followed by the Found New Hardware Wizard screen.

2. Insert the CD into the PC’s CD-ROM Drive and click Next. You will see the following screen.

User’ Guide

19

Image 19

Orion 2000 manual

Contents

Orion Contents Mode of Operation Docsis Configuration File Vsif TAG Support Before You Begin Understand the Cable Modem’s FeaturesContact Your Local Cable Operator Not Supplied Prepare Your Area for Cable Modem InstallationGather Supplied and Required Items Supplied Installing the Software Drivers Before Hardware Connection Installing the Cable Modem Using the USB PortPage Page Installing the Hardware Installing the Software Drivers User’ Guide User’ Guide Page Page Page User’ Guide Page Page User’ Guide Page Page Page User’ Guide None of the LEDs is on when I power on the LAN Cable Modem Troubleshooting the USB Installation Select USB Composite Device and click Remove Click Refresh Uninstalling the USB Driver Installing the Modem Using the Ethernet Port None of the LEDs are on when I power on the Cable Modem Troubleshooting the Ethernet InstallationEnet LED on my cable modem is not lit Cable Modem LEDs and Connectors LEDs on the Front of the Modem Connectors on the Back of the ModemPage Getting Help Telnet commands CMshow ? CMshow interTab CMshow interface Redisplaying a command Debug Ping Image Password CMshow version ¾ show dhcpCMshow dhcp ¾ show version CMshow interface ethernet ¾ show interfaceCMshow interface ? ¾ show interface ethernet ¾ show interface usb CMshow running-configurationCMshow interface usb Qpsk ¾ show downstream Display downstream information ¾ show cpe-info Display CPE information ¾ show upstream ¾ show nat configCMshow nat config CMshow downstream ¾ show user CMshow nat timer¾ show access-list ¾ show nat time ¾ show cpe-limit CMshow access-list¾ show pppoe-forwarding Display PPPoE enable or disable ¾ nvram factory-default ¾ dhcp dns delete 1~4/all CMtftp serverCM dhcp ip-pool add 192.168.100.2 CMshow dhcp ¾ dhcp gateway ip address Set Dhcp gateway ip address ¾ dhcp ip-pool delete 1-20/all CMnat static ipmapping add 68.5.203.16 One to one mapping ¾ nat static ipmapping delete index/all Port forwarding setting NAT static ip CMnat static ip disableCMnat static ip enable CMnat static portmapping delete Interfaces ¾ interface cable startup ¾ interface ethernet startup ¾ rip version 1/2/2b ¾ rip timer expire second Set routing entry expire time CMrip key-chain 1 10 start-time 2002-4-20 ¾ rip default CMaccess-list 41 permit 00d0.5921.3354 ffff.ffff.ffff Web-access ¾ reset ¾ access-list delete list IDall¾ pppoe-forwarding enabledisable Optional CMcopy tftpconfig 68.5.203.15 4ips.txt ¾ quit Disconnect telnet ¾ ip nat enable Mode of OperationBridge mode NAT mode ¾ ip route enable Routing mode ¾ ip natroute enable NAT/Routing mode User’ Guide Cable Modem Information Accessing the Web User InterfaceWeb User Interface Web User Interface Home Cable Modem Status Downstream Upstream Upstream Burst Operation Parameters Event Log Bridge Mode NAT/Router configuration Submit NAT Mode Gateway LAN InterfaceReset WAN Interface Router Mode Routing Protocol LAN Interface Add Key ChainDelete Submit NAT Router Mode Routing Protocol Gateway LAN Interface Authentication mode Authentication Key Chain Submit Gateway LAN Setup Page Meaning Docsis configuration file Vsif tag support