Routing mode, ¾ ip route enable | Orion 2000 specs

Routing mode

¾ip route enable

Default setting for routing mode is RIPv2 with DHCP disabled automatically.

Example:

RIPv2 with MD5 authenication mode enable, key-string “abcdefg”

Public subnet 24.30.206.0/29

•(5) Static Public IPs 24.30.206.2~24.30.206.6

•Gateway IP address 24.30.206.1

Telnet commands:

CM>interface ethernet address 24.30.206.1 mask 255.255.255.248

CM>interface cable rip key-chain 1

CM>interface cable rip auth-mode md5

CM>rip key-chain 1 1 key-string abcdefg

CM>ip route enable

CM>reset

User’ Guide

58

Image 58

Orion 2000 manual Routing mode, ¾ ip route enable

Contents

Orion Contents Mode of Operation Docsis Configuration File Vsif TAG Support Before You Begin Understand the Cable Modem’s FeaturesContact Your Local Cable Operator Supplied Prepare Your Area for Cable Modem InstallationGather Supplied and Required Items Not Supplied Installing the Cable Modem Using the USB Port Installing the Software Drivers Before Hardware ConnectionPage Page Installing the Hardware Installing the Software Drivers User’ Guide User’ Guide Page Page Page User’ Guide Page Page User’ Guide Page Page Page User’ Guide Troubleshooting the USB Installation None of the LEDs is on when I power on the LAN Cable Modem Select USB Composite Device and click Remove Click Refresh Installing the Modem Using the Ethernet Port Uninstalling the USB Driver None of the LEDs are on when I power on the Cable Modem Troubleshooting the Ethernet InstallationEnet LED on my cable modem is not lit Cable Modem LEDs and Connectors Connectors on the Back of the Modem LEDs on the Front of the ModemPage Telnet commands Getting Help CMshow interTab CMshow interface Redisplaying a command CMshow ? Debug Image Ping Password ¾ show version ¾ show dhcpCMshow dhcp CMshow version ¾ show interface ethernet ¾ show interfaceCMshow interface ? CMshow interface ethernet ¾ show interface usb CMshow running-configurationCMshow interface usb Qpsk ¾ show cpe-info Display CPE information ¾ show downstream Display downstream information CMshow downstream ¾ show nat configCMshow nat config ¾ show upstream ¾ show nat time CMshow nat timer¾ show access-list ¾ show user ¾ nvram factory-default CMshow access-list¾ show pppoe-forwarding Display PPPoE enable or disable ¾ show cpe-limit ¾ dhcp dns delete 1~4/all CMtftp serverCM dhcp ip-pool add 192.168.100.2 CMshow dhcp ¾ dhcp ip-pool delete 1-20/all ¾ dhcp gateway ip address Set Dhcp gateway ip address One to one mapping CMnat static ipmapping add 68.5.203.16 Port forwarding setting ¾ nat static ipmapping delete index/all CMnat static portmapping delete CMnat static ip disableCMnat static ip enable NAT static ip Interfaces ¾ interface ethernet startup ¾ interface cable startup ¾ rip timer expire second Set routing entry expire time ¾ rip version 1/2/2b ¾ rip default CMrip key-chain 1 10 start-time 2002-4-20 Web-access CMaccess-list 41 permit 00d0.5921.3354 ffff.ffff.ffff CMcopy tftpconfig 68.5.203.15 4ips.txt ¾ access-list delete list IDall¾ pppoe-forwarding enabledisable Optional ¾ reset ¾ quit Disconnect telnet NAT mode Mode of OperationBridge mode ¾ ip nat enable Routing mode ¾ ip route enable NAT/Routing mode ¾ ip natroute enable User’ Guide Web User Interface Home Accessing the Web User InterfaceWeb User Interface Cable Modem Information Cable Modem Status Downstream Upstream Upstream Burst Operation Parameters Event Log NAT/Router configuration Bridge Mode WAN Interface NAT Mode Gateway LAN InterfaceReset Submit Router Mode Routing Protocol LAN Interface Add Key ChainDelete Submit NAT Router Mode Routing Protocol Gateway LAN Interface Authentication mode Authentication Key Chain Submit Gateway LAN Setup Page Docsis configuration file Vsif tag support Meaning