Manuals / Orion / Computer Equipment / Network Router

Orion 2000 RIP status Enable RIP send version Downstream information, Upstream Mini-Slot Size

Models: 2000

1 80

Download 80 pages 4.16 Kb

Page 40

RIP status: Enable

RIP send version: 2

Downstream information

FEC Lock : Locked

Downstream Frequency : 741000000 Hz

Downstream Modulation : 64 QAM

Downstream Interleave Depth : 32

Downstream Receive Power Level : -11.44 dBmv

Downstream SNR : 30.03 dB

Upstream information

Upstream Channel ID : 1

Upstream Transmit Power Level : 46.00 dBmv

Upstream Symbol Rate : 2560 ksym/sec

Upstream Frequency : 32784000 Hz

Upstream Mini-Slot Size : 8

Upstream Burst Descriptor :		Periodic
	Initial	Periodic	Ranging(4)	shortData(5)	longData(6)
Modulation Type	request(1) Ranging(3)		Ranging(4)	shortData(5)	longData(6)
Modulation Type	QPSK	QPSK	QPSK	QPSK	QPSK
Differential	off	off	off	off	off
Preamble Length	64	128	128	72	80
Preamble Value	952	896	896	944	936
FEC Error	no FEC	5	5	5	8
FEC Codeword	16	34	34	75	220
Scrambler Seed	338	338	338	338	338
Maximum Burst Size 0		0	0	6	0
Guard Time Size	8	48	48	8	8
Last Codeword	fixed	fixed	fixed	fixed	fixed
Scrambler on/off	on	on	on	on	on

Interface Ethernet

MAC address: 0002.8A32.4102

IP address 24.196.57.13 subnet-mask 255.255.255.252

Link status: link

Mode: 100Mbps, full-duplex

RIP status: Enable

RIP send version: 2

Interface USB

USB-Host MAC address: 0002.8A32.4103

Speed: 12Mbps

Link status: disconnect

Cable Modem mode : Router

RIP parameter

Routing protocol: RIPv2

RIP update time: 15 seconds

RIP response time: 30 secconds

User’ Guide

40

Image 40

Orion 2000 RIP status Enable RIP send version Downstream information, FEC Lock Locked Downstream Frequency 741000000 Hz

Contents

Orion Cable RouterUser’s Guide Rev. 1.2a2. INSTALLING THE CABLE MODEM USING THE USB PORT 3. INSTALLING THE MODEM USING THE ETHERNET PORT4. CABLE MODEM LEDS AND CONNECTORS 5. TELNET COMMANDSUser’ Guide 6. MODE OF OPERATIONDebug 7. WEB USER INTERFACE 9. DOCSIS CONFIGURATION FILE VSIF TAG SUPPORTUser’ Guide Understand the Cable Modem’s Features Limitations set by your Cable Service Provider1. Before You Begin Contact Your Local Cable OperatorPrepare Your Area for Cable Modem Installation Gather Supplied and Required ItemsSupplied Not Supplied2. Installing the Cable Modem Using the USB Port Installing the Software Drivers Before Hardware Connection1. Double click the “Setup.exe” program in the CD 3. You will see the following Welcome screen4. Click “Next”. You will see the following Start screen User’ Guide5. Click “Next”. You will see the following ‘Complete’ screen User’ GuideInstalling the Hardware Installing the Software Drivers Installing the Software Drivers in Windows 98 SE Operating SystemUser’ Guide CAUTION You must verify that Ambit USB Cable Modem appears on the screen. If USB Composite Device appears, you must click Back twice and specify the correct location of the driver files. DO NOT proceed if USB Composite Device is displayed in the above window. Contact your cable provider for further assistance User’ Guide 8. After files copying is done, you will see the following screen User’ GuideInstalling the Software Drivers in Windows Me Operating System User’ Guide 6. Click Yes to restart the computer User’ GuideInstalling the Software Drivers in Windows 2000 Operating System User’ Guide User’ Guide Installing the Software Drivers in Windows XP Operating System User’ Guide User’ Guide None of the LEDs is on when I power on the LAN Cable Modem Troubleshooting the USB Installation2. Click the Device Manager tab 4. Select USB Composite Device and click Remove 5. Click Refresh 3. Installing the Modem Using the Ethernet Port Uninstalling the USB DriverTroubleshooting the Ethernet Installation None of the LEDs are on when I power on the Cable ModemThe ENET LED on my cable modem is not lit Installing the Hardware4. Cable Modem LEDs and Connectors Connectors on the Back of the Modem LEDs on the Front of the ModemUser’ Guide Note Cable Modem Router Telnet IP address is 5. Telnet commandsGetting Help CMshow interTab CMshow interface Redisplaying a command CMshow ?Debug Undebug¾ debug CMdebug ?¾ image upgrade CMimage upgradeImage PingPassword CMpwd adminCMuser-level admin ¾ show config-file¾ show dhcp CMshow dhcp¾ show version CMshow version¾ show interface CMshow interface ?¾ show interface ethernet CMshow interface ethernet¾ show running-configuration Display system running information CMshow running-configuration CMshow running-config¾ show interface usb CMshow interface usbRIP status Enable RIP send version Downstream information Downstream Receive Power Level -11.44 dBmv Downstream SNR 30.03 dBUpstream Transmit Power Level 46.00 dBmv Upstream Symbol Rate 2560 ksym/sec Upstream Frequency 32784000 Hz¾ show cpe-info Display CPE information CMshow cpe-infoPort 0002.8A0E.E674¾ show nat config CMshow nat configCMshow downstream ¾ show upstreamCMshow nat timer admin¾ show access-list ¾ show nat timeCMshow access-list ¾ show pppoe-forwarding Display PPPoE enable or disable¾ nvram factory-default NVRAM¾ dhcp enable/disable Enable/disable dhcp server Note if NAT is enabled, the following DHCP command can bet setDHCP ¾ tftp server Server IP address¾ dhcp ip-pool delete 1-20/all ¾ dhcp gateway ip address Set DHCP gateway ip addressCMdhcp reserve-mac add 192.168.100.4 0002.8A25.251D CMshow dhcp Example¾ ip nat enable/disable One to one mappingCMnat static ipmapping add 68.5.203.16 CMshow nat configPort forwarding setting CMshow nat config NAT Enable¾ nat static ipmapping delete index/all CMnat static portmapping add 21 192.168.100.23 ftp¾ nat static ip enabledisableipaddress CMnat static ip disableCMnat static ip enable CMnat static portmapping deleteInterfaces CMinterface ethernet address 192.168.100.1 mask¾ interface ethernet mac-address mac address CMinterface ethernet mac-address 0008.0E86.1118¾ interface ethernet shutdown ¾ interface ethernet startup¾ interface cable upstream channel id Change upstream channel ID ¾ interface cable shutdown¾ ip route enable/disable ¾ ip natroute enable/disable¾ ip nat enable/disable Enable/disable NAT/PAT function ¾ rip timer update second Set routing table update time¾ rip default CMrip key-chain 1 10 start-time 2002-4-20CMrip key-chain 1 5 key-string abcdefg CM interface ethernet auth-mode md5Web-access Access-listCMaccess-list 41 permit 00d0.5921.3354 ffff.ffff.ffff ExampleReset ¾ access-list delete list IDall¾ pppoe-forwarding enabledisable Optional ¾ copy tftpconfig tftp server ip address configuration filenameQuit ¾ quit Disconnect telnet6. Mode of Operation Bridge modeNAT mode ¾ ip nat enableRouting mode ¾ ip route enableCMrip key-chain 1 1 key-string abcdefg CMip route enable CMreset CMinterface ethernet address 24.30.206.1 maskNAT/Routing mode ¾ ip natroute enableTelnet commands ExampleCMinterface cable rip auth-mode md5 CMrip key-chain 1 1 key-string abcdefg CMip natroute enable CMresetUser’ Guide Accessing the Web User Interface 7. Web User InterfaceWeb User Interface Home Page Cable Modem InformationCable Modem Status User’ GuideDownstream User’ GuideUpstream User’ GuideUpstream Burst User’ GuideOperation Parameters User’ GuideEvent Log User’ GuideNAT/Router configuration Bridge ModeNAT Mode Gateway LAN Interface ResetWAN Interface SubmitRouter Mode User’ GuideRouting Protocol LAN Interface Public IP Address subnet mask RIP status Authentication modeAuthentication Key Chain Private IP Address subnet mask RIP status Authentication modeDelete Key ChainKey Chain Reset Click “Reset” to use displayed parameters, cable modem will resetSubmit Click “Submit” to change displayed parametersNAT Router Mode Routing Protocol User’ GuideLAN Interface Gateway LAN InterfaceWAN Interface Authentication mode Authentication Key Chain Key ChainListing of key Input key Index ID, Key String, Start time, and End timeReset Click “Reset” to use displayed parameters, cable modem will resetListing of key Chain Input key Index ID, Key String, Start time, and End timeGateway LAN Setup DHCPIP-pool Default IP-pool 1 supports 192.168.100.2~192.168.100.21 Domain Name ServiceUser’ Guide 9. DOCSIS configuration file VSIF tag support Meaningcopy tftpconfig 172.21.1.250 cmconfig.txt Pwd admin Cableroot abcdefg rip key-chain1 1key-string cablerouter