1. Parts and their functions

1-2. Rear panel area

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SV NM

 

 

 

 

 

POWER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EDITOR

 

COM

 

TALLY/GPI 2

TALLY/GPI 1

BOOT

 

REF

 

 

 

 

ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF

 

IN/OUT B2

IN/OUT B1

 

 

 

IN/OUT A2

 

IN/OUT A1

 

 

 

 

 

～AC IN

 

 

 

 

 

 

 

 

 

 

 

 

SLOT B

 

 

 

 

 

 

SLOT A

 

 

 

 

 

 

 

 

DVI-D OUT

DVI-D IN

 

 

SDI OUTPUTS

 

 

 

 

SDI INPUTS

 

 

 

LAN

SIGNAL

 

 

5

4

3

2

1

8

7

6

5

4

3

2

1

 

GND

  

Power switch [POWER]

When the power switch is turned on, the POWER indicator () lights up, and the unit can be operated.

  

LAN connector [LAN] (RJ-45) (10/100 Base-TX)

Refer to “4. External interfaces” (<Operations and Settings> Operating Instructions).

SDI signal input connectors [SDI INPUTS 1 to 8]

The up-converter function can be used for the SDI INPUT 5 to SDI INPUT 8 connectors.

Option slot SLOT A [IN/OUT A1, IN/OUT A2] Option slot SLOT B [IN/OUT B1, IN/OUT B2]

Each of these is an input/output option slot.

A DVI input board, analog output board or other option board can be installed in these slots.

For details, refer to “How to install the option boards” (on page 12) and the operating instructions of the board concerned.

SDI signal output connectors [SDI OUTPUTS 1 to 5]

These can be allocated by the menus.

ppTwo sets of the same output signals are distributed from the SDI OUTPUT 1 connector.

DVI-D input connector [DVI-D IN]

Connect to the computer with the DVI-D cable. ppThe DVI-I connector cable cannot be used.

DVI-D output connector [DVI-D OUT]

Connect a monitor that supports DVI-D. It can be allocated by the menus.

ppThe DVI-I connector cable cannot be used.

Reference input connector/BB output connector [REF]

Loop-through output in the external sync mode.

If the loop-through output is not going to be used, provide a 75-ohm termination.

BB signals output from both connectors in the internal sync mode.

EDITOR connector [EDITOR]

(RS-422, D-sub 9-pin, female, inch screw)

COM connector [COM]

(RS-422, D-sub 9-pin, female, inch screw)

Refer to “4. External interfaces” (<Operations and Settings> Operating Instructions).

TALLY/GPI input/output connectors [TALLY/GPI 1, TALLY/GPI 2] (D-sub 15-pin, female, inch screw)

Refer to “4. External interfaces” (<Operations and Settings> Operating Instructions).

Ground connector [SIGNAL GND]

Connect to the system’s earth ground.

AC power input socket [ AC IN] (AC 100 V to 240 V, 50/60 Hz)

Connect one end of the supplied power cable to this socket and the other end to the AC outlet.

The supplied power cable comes with a 3-pin power plug. Be absolutely sure to plug it into a 3-point power outlet as the power source in order to earth the unit securely.

If a 3-point power outlet is not available for this connection, be absolutely sure to consult your dealer.

Cooling fan

BOOT switch [BOOT]

This switch is used for maintenance purposes.

For normal operations, select the “NM” (normal) position.

27