Removing a Misfed Paper, Paper Transport Area

Problem Solving

Removing a Misfed Paper

■ Paper Transport Area

CMake sure that the misfeed indicator goes off after removing all misfed paper.

1	Push the latch to open the cover.
	Push the latch to open the cover.
2	Remove the misfed paper.
	Remove the misfed paper.
3	Close the cover by pushing the
	latch.
	(Check that the latch is securely
	fastened.)

ATTENTION	CMake sure that the misfeed indicator goes off after removing all misfed paper.

Page 50

Image 50

Panasonic DP-200 manual Removing a Misfed Paper, Paper Transport Area

Contents

DP-2000 English Operation Chart Common Features and Usage Energy Star Table of Contents Others Problem SolvingOptions Laser Safety PrecautionsFor Your Safety Precautions Handling Toner and Paper Ventilation Installation FCC Warning For U.S.A Control Panel Clear Keys Contents Refer to Function KeyReset Key Stop Key Margin Key Contents Refer to Book KeyEdge Key Cursor Keys Basic Copy Full Size Copying Select the Copy Copying with Preset RatiosReduction or Enlargement Copying Size Press Cursor F or G keys to select Zoom Ratio Zoom CopyingZoom Copying on Special Paper, etc Using the Sheet Bypass$Adjust the side guides # Place approximately 50 sheets of paper into the tray Key Operation Sided/Original H Copy Duplex CopySided/1-Sided Copy Book \ Press 2-Sided Procedure\ 2/2 \ 1/2 \ 2 Copy Sided Copy key Book \ 2 Copy Book \ 2 CopyPlace the Original on the Platen Platen 1 key 1 CopyPress 1 Copy Key CopyPlace Press Originals Press Book, Edge or MarginBook/Edge/Margin Margin key OHP Interleaving OHP InterleavingPress the Copied key or the Blank key Blank Paper To store a job in memory To recall a job stored in memory Sleep Mode Energy Saver/Interrupt ModeEnergy Saver Mode Interrupt Mode Proceed as Follows Skyshot ModeSetting the Digital Skyshot Mode Set Manual Skyshot mode first Platen Upper- left corner Copying with the Manual Skyshot ModeSetting the Manual Skyshot Mode Press the Function Key Copy Combined Function TableSort SIDED/ORIG Options Using Function Modes to Change the Initial Copy ModesFunction Input Identification Code Modes Function Initial Setting General Functions Copier Settings General Functions for Key Operator Copier Settings for Key Operator Function Setting Changing the Auto Exposure Setting Function Setting for Key Operator Changing the Paper Size Paper Guide a Stopper Guide b Departmental Counter Counter 6 digits Accessories Components ADF DA-AS200/i-ADF DA-AR250 FeaturesAutomatic Document Feeder Components Original OperationPlace Inappropriate originals Platen Face-Up Finisher/Exit Guide UnitDA-FS200 Finisher Press Sort/Finish key Replacing the staple cartridge Pull out the tape Reinstall the staple cartridge #Open the staple cover Sheet Paper Tray Problem SolvingAdding Paper J Slowly pull the waste toner box Replacing the Toner Cartridge and Waste Toner Box ?Open the front cover Straight out Shake the new toner cartridge Install the new toner cartridge intoInstall a new waste toner box Well Paper Misfeed Locations Misfeed IndicatorRemoving a Misfeed Paper Finisher Removing a Misfed Paper Paper Transport Area Paper Entry Area Open the right cover Automatic Duplex Unit ADU Close the right cover System Console ADF/i-ADF #Lift up the ADF Input Tray Check TroubleshootingBefore Calling Service Action Marked Copies As a rule, clean weeklyLight Copies Platen Cover Battery Replacement Procedure Replacing the BatteryBattery Replacement Required Message Specifications DP-2000 Copier 2nd/3rd/4th Paper Feed Module DA-DS210/DA-DS200 ADF DA-AS200, i-ADF DA-AR250Bin Finisher DA-FS200 Options and Supplies Part Name Remarks For Fax For Printer Warranty

Removing a Misfed Paper

■ Paper Transport Area

latch.