Paper Entry Area, Open the right cover | Panasonic DP-200 instruction

Problem Solving

■ Paper Entry Area

CMake sure that the misfeed indicator goes off after removing all misfed paper.

1	Open the right cover.

2	Remove the misfed paper.

Continued on the next page...

#Open the heat roller cover.

$If copy paper is fed far into the copier, turn the right paper clearing knob.

%Remove the misfed paper.

ATTENTION CMake sure that the misfeed indicator goes off after removing all misfed paper.

Page 51

Image 51

Panasonic DP-200 manual Paper Entry Area, Open the right cover

Contents

English DP-2000 Common Features and Usage Operation Chart Energy Star Table of Contents Problem Solving OptionsOthers Precautions For Your SafetyLaser Safety Handling Toner and Paper Ventilation Precautions FCC Warning For U.S.A Installation Control Panel Stop Key Contents Refer to Function KeyReset Key Clear Keys Cursor Keys Contents Refer to Book KeyEdge Key Margin Key Full Size Copying Basic Copy Size Copying with Preset RatiosReduction or Enlargement Copying Select the Copy Zoom Copying ZoomPress Cursor F or G keys to select Zoom Ratio # Place approximately 50 sheets of paper into the tray Using the Sheet Bypass$Adjust the side guides Copying on Special Paper, etc Book \ Sided/Original H Copy Duplex CopySided/1-Sided Copy Key Operation Sided Copy key Procedure\ 2/2 \ 1/2 \ 2 Copy Press 2-Sided Platen Book \ 2 CopyPlace the Original on the Platen Book \ 2 Copy 1 Copy 1 CopyPress 1 key Copy Place Press OriginalsKey Margin key MarginBook/Edge/Margin Press Book, Edge or Blank Paper OHP InterleavingPress the Copied key or the Blank key OHP Interleaving To recall a job stored in memory To store a job in memory Interrupt Mode Energy Saver/Interrupt ModeEnergy Saver Mode Sleep Mode Skyshot Mode Setting the Digital Skyshot ModeProceed as Follows Copying with the Manual Skyshot Mode Setting the Manual Skyshot Mode Press the Function KeySet Manual Skyshot mode first Platen Upper- left corner SIDED/ORIG Combined Function TableSort Copy Input Identification Code Using Function Modes to Change the Initial Copy ModesFunction Options General Functions Modes Function Initial Setting Copier Settings General Functions for Key Operator Copier Settings for Key Operator Changing the Auto Exposure Setting Function Setting Changing the Paper Size Function Setting for Key Operator Paper Guide a Stopper Guide b Departmental Counter Counter 6 digits Components Accessories Components FeaturesAutomatic Document Feeder ADF DA-AS200/i-ADF DA-AR250 Inappropriate originals OperationPlace Original Press Sort/Finish key Finisher/Exit Guide UnitDA-FS200 Finisher Platen Face-Up Pull out the tape Replacing the staple cartridge Reinstall the staple cartridge #Open the staple cover Problem Solving Adding Paper JSheet Paper Tray Straight out Replacing the Toner Cartridge and Waste Toner Box ?Open the front cover Slowly pull the waste toner box Well Install the new toner cartridge intoInstall a new waste toner box Shake the new toner cartridge Misfeed Indicator Removing a Misfeed PaperPaper Misfeed Locations Finisher Paper Transport Area Removing a Misfed Paper Open the right cover Paper Entry Area Close the right cover Automatic Duplex Unit ADU System Console ADF/i-ADF #Lift up the ADF Input Tray Action TroubleshootingBefore Calling Service Check Platen Cover As a rule, clean weeklyLight Copies Marked Copies Replacing the Battery Battery Replacement Required MessageBattery Replacement Procedure DP-2000 Copier Specifications ADF DA-AS200, i-ADF DA-AR250 Bin Finisher DA-FS2002nd/3rd/4th Paper Feed Module DA-DS210/DA-DS200 Part Name Remarks Options and Supplies For Printer For Fax Warranty

■ Paper Entry Area

Open the right cover.

Continued on the next page...