Replacing the staple cartridge | Panasonic DP-200 specification

Accessories

Finisher/Exit Guide Unit

3. Replacing the staple cartridge

ADD STAPLES

U11

The message shown on the left appears when the staples run out.

Hold the latch and pull out the finisher.

2	Remove the staple cartridge.
	Remove the staple cartridge.
3	#Remove the empty staple case.
	#Remove the empty staple case.
	$Install the new staple case.

4	Pull out the tape.

Page 42

Image 42

Panasonic DP-200 manual Replacing the staple cartridge, Pull out the tape

Contents

DP-2000 English Operation Chart Common Features and Usage Energy Star Table of Contents Problem Solving OptionsOthers Precautions For Your SafetyLaser Safety Precautions Handling Toner and Paper Ventilation Installation FCC Warning For U.S.A Control Panel Clear Keys Contents Refer to Function KeyReset Key Stop Key Margin Key Contents Refer to Book KeyEdge Key Cursor Keys Basic Copy Full Size Copying Select the Copy Copying with Preset RatiosReduction or Enlargement Copying Size Zoom Copying ZoomPress Cursor F or G keys to select Zoom Ratio Copying on Special Paper, etc Using the Sheet Bypass$Adjust the side guides # Place approximately 50 sheets of paper into the tray Key Operation Sided/Original H Copy Duplex CopySided/1-Sided Copy Book \ Press 2-Sided Procedure\ 2/2 \ 1/2 \ 2 Copy Sided Copy key Book \ 2 Copy Book \ 2 CopyPlace the Original on the Platen Platen 1 key 1 CopyPress 1 Copy Copy Place Press OriginalsKey Press Book, Edge or MarginBook/Edge/Margin Margin key OHP Interleaving OHP InterleavingPress the Copied key or the Blank key Blank Paper To store a job in memory To recall a job stored in memory Sleep Mode Energy Saver/Interrupt ModeEnergy Saver Mode Interrupt Mode Skyshot Mode Setting the Digital Skyshot ModeProceed as Follows Copying with the Manual Skyshot Mode Setting the Manual Skyshot Mode Press the Function KeySet Manual Skyshot mode first Platen Upper- left corner Copy Combined Function TableSort SIDED/ORIG Options Using Function Modes to Change the Initial Copy ModesFunction Input Identification Code Modes Function Initial Setting General Functions Copier Settings General Functions for Key Operator Copier Settings for Key Operator Function Setting Changing the Auto Exposure Setting Function Setting for Key Operator Changing the Paper Size Paper Guide a Stopper Guide b Departmental Counter Counter 6 digits Accessories Components ADF DA-AS200/i-ADF DA-AR250 FeaturesAutomatic Document Feeder Components Original OperationPlace Inappropriate originals Platen Face-Up Finisher/Exit Guide UnitDA-FS200 Finisher Press Sort/Finish key Replacing the staple cartridge Pull out the tape Reinstall the staple cartridge #Open the staple cover Problem Solving Adding Paper JSheet Paper Tray Slowly pull the waste toner box Replacing the Toner Cartridge and Waste Toner Box ?Open the front cover Straight out Shake the new toner cartridge Install the new toner cartridge intoInstall a new waste toner box Well Misfeed Indicator Removing a Misfeed PaperPaper Misfeed Locations Finisher Removing a Misfed Paper Paper Transport Area Paper Entry Area Open the right cover Automatic Duplex Unit ADU Close the right cover System Console ADF/i-ADF #Lift up the ADF Input Tray Check TroubleshootingBefore Calling Service Action Marked Copies As a rule, clean weeklyLight Copies Platen Cover Replacing the Battery Battery Replacement Required MessageBattery Replacement Procedure Specifications DP-2000 Copier ADF DA-AS200, i-ADF DA-AR250 Bin Finisher DA-FS2002nd/3rd/4th Paper Feed Module DA-DS210/DA-DS200 Options and Supplies Part Name Remarks For Fax For Printer Warranty

Finisher/Exit Guide Unit

3. Replacing the staple cartridge

Pull out the tape.