Make a hole for a cable | Panasonic KX-HCM280 manual

Operating Instructions

2.Make a hole for a cable.

Hole for a cable: 25 mm (1 inch)

65 mm (2.5 inches)

3.Fix the rubbers and dents of Network Camera to the Ceiling Plate A and fix them firmly.

•Make sure Network Camera, using coins etc., is firmly fixed.

Fit the four rubbers in place.

Fit the two dents in place.

4.Fix the Ceiling Plate A to the Ceiling Plate B and fix them firmly with Screws A.

Four Tabs

Fit the hooks to the holes and move in the counterclockwise direction.

Screws A (2 pcs.)

Fix firmly with Screws A.

Note

Install Network Camera so that the connecting part comes to the front.

100

Image 100

Panasonic KX-HCM280 operating instructions Make a hole for a cable

Contents

Network Camera Screws B For operation assistance Call Network Camera Memo TrademarksFor assistance, please call Important Safety Instructions Table of Contents Technical Guides Specifications and Troubleshooting 108Index 131 Section Main Features Getting to Know Network Camera Multi-Client Access Update FirmwareAuthentication Video Output System Requirements Authentication-System Security Feature Authentication window Included Accessories Setup CD-ROM Camera Feature Locations Lens Power Focus/Zoom LensIndicator Front View Rear View Bottom View Network Camera Setup Installation Procedure Network Camera can be installed on the LAN/Intranet Network Camera Configuration TypeType 2-Internet Connection with a Broadband Router Type 4-Direct Connection with a PC Type 3-Internet Direct Connection with a ModemNetwork Camera can be connected to a PC directly How to turn on Network Camera for Installation Preparing the Network Parameters for Network Camera Network ParametersNetwork parameters memo for Network Camera Network Camera Configuration Type DefaultNetwork Parameters Table Type Port No How to refer the network parameters from the PC Enter winipcfg and click OK. IP configuration window appears Setting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Network Camera Access from the Internet Port Forwarding IP Masquerade feature Top If Top Page does not appear Operating Instructions Network Camera Screen and Setup Window Network Camera Flow Chart Example TopHttp//Global IP address of Broadband RouterPortNo Top Motion Jpeg Single CameraMulti-Camera Help ActiveX Controls Single Camera Screen Click to Center Using Operation Bar Pan/Tilt Scan, Pan/Tilt and Home Position Refer to Using Pan/Tilt Operation On the table On the ceiling Operating Instructions Zooming in and out Automatic and Manual Focusing Objects that are difficult to focus on by AF button Minimum object distance Setting Preset Positioning and Home Positioning Home Position Deleting the preset buttons Click Delete Non Transfer mode Alarm/Timer mode Viewing Buffered Image Screen Viewer Clicking Start CapturePrimary Secondary Multi-Camera Screen Viewing Images from Network Camera on TV Setup Setup Administrator Camera SetupGo to Top Name/Time Indicator Control Reset to FactoryExternal Output Control Go to Top Network Instructions for the data fields Enter only the number If you use Network Camera on the LAN, set up Check Dhcp Dynamic Host Configuration ProtocolSubnet Mask Mask Ddns File size of the image Name/Time CameraName Date Adjustment Time Changed AM/PM or 24HAuto Time Zone Security Administrator Click Security Administrator on Setup For Setup Password EnableRetype Click Security General User on Setup Security General User Delete or Modify User ID ListNew User Top View Image Resolution Instructions for the data fields TopImage 160 x Image Quality Image Transfer Non Transfer mode Transfer in the Alarm Mode Click Alarm on Image Transfer window Sets the image resolution and image quality Alarm enable conditionActive Time of Trigger Login timing Over write setting Data transfer method Setting Example Setting explanation Transfer in the Timer Mode Buffers or transfers by the timer trigger Login timing Over write setting Camera Setup White Balance is also registered in preset programming SuggestedFocus Control Focus Control can be locked Having reached the selected end Click Save when finished Specifying the Pan/Tilt range Multi-Camera Enable check box IP Address orURL * 1 or Host Camera Name Click External Output Control on Setup External Output Control Indicator Control Status Restart Click Cancel to quit. The window returns to SetupClick Restart Now Update Firmware Click Update Firmware on Setup Click Update Firmware Operating Instructions Reset to Factory Default Technical Guides Mounting Mounting on the Table Wiring through a hole made in the ceiling Mounting on the Ceiling Make a hole for a cable Wiring without making a hole for a cable in the ceiling Ceiling Mounting example Making holes on mortar wall Interfacing to the External I/O Explanation of External I/OPin Function External Sensor Input Circuit Diagram Example Ascii and ISO-8859-1 Character Table Unavailable character setSpace, , , #, &, %, =, +, ?, , and are not available For assistance, please call 105 Displayable character set 106 Lens MaintenanceFor assistance, please call 107 Specifications and Troubleshooting 108 Network Camera Reset Procedure-Default Settings Default Settings List Items Factory Default Indispensable setting Value Network Alarm For assistance, please call 111 Items Factory Default Indispensable setting Value Alarm 112 Items Factory Default Indispensable setting Value Timer For assistance, please call 113 Setup 114 Update Firmware For assistance, please call 115 Specifications Network Camera Specifications DescriptionOther Specifications Description 116 When detecting the alarm Message Transferring MethodOperation/Ethernet link Situation in Buffered Image Operating Instructions About Network Camera Setup TroubleshootingProblem Cause and Remedy LAN. Refer to For Indicator Control window Network window on Transfers older About Network Camera Setup Problem Cause and Remedy Update About Top View Image screen Click Tools -Internet Options -Security tab Automatic Focusing feature. Clean the lens with lens CleanerManual focusing may be set. Press appropriate one Blurred images may have been registered when registering View Image Setting window on About Other Troubles Confirmation of Network Camera Operation Click the language to change the display FCC and Other Information 130 Index 131 Operating Instructions TCP/IP For product service When you ship the product