External Output Control | Panasonic KX-HCM280 guide

Operating Instructions

3.6.10 External Output Control

External Output Control window enables the External Device Control Output signal to activate the external sensors/devices. (Open or Short to GND) The network administrator should set up this setting.

1.

2.

3.

Note

Refer to page 103 for Interfacing to the External I/O.

Click [External Output Control] on Setup Page.

Check [Open] means the External Device Control Output becomes high impedance (open collector).

Check [Short to GND] means the External Device Control Output becomes low (0V).

Click [Save] to send the signal.

•Click [Cancel] to quit the current settings. The window returns to Setup Page without saving the parameters.

[For assistance, please call: 1-800-272-7033]

89

Image 89

Panasonic KX-HCM280 operating instructions Click External Output Control on Setup

Contents

Network Camera For operation assistance Call Screws B For assistance, please call TrademarksNetwork Camera Memo Important Safety Instructions Table of Contents Index 131 Specifications and Troubleshooting 108Technical Guides Section Getting to Know Network Camera Main Features Update Firmware Multi-Client AccessAuthentication Video Output System Requirements Authentication window Authentication-System Security Feature Included Accessories Setup CD-ROM Lens Power Focus/Zoom Lens Camera Feature LocationsIndicator Front View Bottom View Rear View Network Camera Setup Installation Procedure Type 2-Internet Connection with a Broadband Router Network Camera Configuration TypeNetwork Camera can be installed on the LAN/Intranet Network Camera can be connected to a PC directly Type 3-Internet Direct Connection with a ModemType 4-Direct Connection with a PC How to turn on Network Camera for Installation Network parameters memo for Network Camera Network ParametersPreparing the Network Parameters for Network Camera Default Network Camera Configuration TypeNetwork Parameters Table Type Port No Enter winipcfg and click OK. IP configuration window appears How to refer the network parameters from the PC Setting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Port Forwarding IP Masquerade feature Network Camera Access from the Internet If Top Page does not appear Top Operating Instructions Network Camera Screen and Setup Window Network Camera Flow Chart Http//Global IP address of Broadband RouterPortNo Top TopExample Single Camera Motion JpegMulti-Camera Help ActiveX Controls Single Camera Screen Click to Center Pan/Tilt Scan, Pan/Tilt and Home Position Refer to Using Operation Bar On the table On the ceiling Using Pan/Tilt Operation Operating Instructions Zooming in and out Objects that are difficult to focus on by AF button Automatic and Manual Focusing Minimum object distance Setting Preset Positioning and Home Positioning Home Position Click Delete Deleting the preset buttons Viewing Buffered Image Screen Non Transfer mode Alarm/Timer mode Clicking Start Capture ViewerPrimary Secondary Multi-Camera Screen Viewing Images from Network Camera on TV Setup Setup Camera Setup AdministratorGo to Top Name/Time Reset to Factory Indicator ControlExternal Output Control Go to Top Network Enter only the number Instructions for the data fields Check Dhcp Dynamic Host Configuration Protocol If you use Network Camera on the LAN, set upSubnet Mask Mask File size of the image Ddns Camera Name/TimeName Date Time Changed AM/PM or 24H AdjustmentAuto Time Zone Click Security Administrator on Setup Security Administrator Retype EnableFor Setup Password Security General User Click Security General User on Setup New User User ID ListDelete or Modify Top View Image Instructions for the data fields Top ResolutionImage 160 x Image Quality Image Transfer Non Transfer mode Click Alarm on Image Transfer window Transfer in the Alarm Mode Active Time of Trigger Alarm enable conditionSets the image resolution and image quality Over write setting Login timing Data transfer method Setting Example Setting explanation Transfer in the Timer Mode Buffers or transfers by the timer trigger Login timing Over write setting Camera Setup Suggested White Balance is also registered in preset programmingFocus Control Focus Control can be locked Having reached the selected end Specifying the Pan/Tilt range Click Save when finished Multi-Camera IP Address or Enable check boxURL * 1 or Host Camera Name External Output Control Click External Output Control on Setup Indicator Control Status Click Restart Now Click Cancel to quit. The window returns to SetupRestart Update Firmware Click Update Firmware Click Update Firmware on Setup Operating Instructions Reset to Factory Default Technical Guides Mounting on the Table Mounting Mounting on the Ceiling Wiring through a hole made in the ceiling Make a hole for a cable Wiring without making a hole for a cable in the ceiling Ceiling Mounting example Making holes on mortar wall Explanation of External I/O Interfacing to the External I/OPin Function External Sensor Input Circuit Diagram Example Unavailable character set Ascii and ISO-8859-1 Character TableSpace, , , #, &, %, =, +, ?, , and are not available For assistance, please call 105 106 Displayable character set For assistance, please call 107 MaintenanceLens 108 Specifications and Troubleshooting Network Camera Reset Procedure-Default Settings Items Factory Default Indispensable setting Value Network Default Settings List For assistance, please call 111 Alarm 112 Items Factory Default Indispensable setting Value Alarm For assistance, please call 113 Items Factory Default Indispensable setting Value Timer 114 Setup For assistance, please call 115 Update Firmware Network Camera Specifications Description SpecificationsOther Specifications Description 116 Message Transferring Method When detecting the alarmOperation/Ethernet link Situation in Buffered Image Operating Instructions Problem Cause and Remedy TroubleshootingAbout Network Camera Setup LAN. Refer to For Indicator Control window Transfers older Network window on Update About Network Camera Setup Problem Cause and Remedy Click Tools -Internet Options -Security tab About Top View Image screen Cleaner Automatic Focusing feature. Clean the lens with lensManual focusing may be set. Press appropriate one Blurred images may have been registered when registering About Other Troubles View Image Setting window on Confirmation of Network Camera Operation Click the language to change the display FCC and Other Information 130 131 Index Operating Instructions TCP/IP When you ship the product For product service