Network Parameters | Panasonic KX-HCM280 instruction

Operating Instructions

2.4Network Parameters

2.4.1Preparing the Network Parameters for Network Camera

Before starting to set up the network parameters of Network Camera, make note of corresponding network parameters.

[Type 1] Ask your network administrator for the network parameters.

[Type 2] Refer to the broadband router’s manual for the network parameters.

[Type 3] Ask your ISP (Internet Service Provider) for the network parameters.

[Type 4] Install Network Camera in the default condition. Set the PC "192.168.0.250" (IP address) and "255.255.255.0" (Subnet Mask). Refer to page 24.

Refer to page 22 and page 23 for network parameters.

Network parameters memo for Network Camera

The devices on the network may not be assigned the same IP address. Each device must have its own IP address. Overlapped IP addresses can cause other network devices to stop working and may result in widespread network problems.

IP Address	.	.	.
Default Gateway	.	.	.

Subnet Mask	.	.		.
DNS Server 1		.	.	.

DNS Server 2

.

.

.

[For assistance, please call: 1-800-272-7033]

21

Image 21

Panasonic KX-HCM280 Preparing the Network Parameters for Network Camera, Network parameters memo for Network Camera

Contents

Network Camera For operation assistance Call Screws B Trademarks Network Camera MemoFor assistance, please call Important Safety Instructions Table of Contents Specifications and Troubleshooting 108 Technical GuidesIndex 131 Section Getting to Know Network Camera Main Features Update Firmware Multi-Client AccessAuthentication Video Output System Requirements Authentication window Authentication-System Security Feature Included Accessories Setup CD-ROM Lens Power Focus/Zoom Lens Camera Feature LocationsIndicator Front View Bottom View Rear View Network Camera Setup Installation Procedure Network Camera Configuration Type Network Camera can be installed on the LAN/IntranetType 2-Internet Connection with a Broadband Router Type 3-Internet Direct Connection with a Modem Type 4-Direct Connection with a PCNetwork Camera can be connected to a PC directly How to turn on Network Camera for Installation Network Parameters Preparing the Network Parameters for Network CameraNetwork parameters memo for Network Camera Default Network Camera Configuration TypeNetwork Parameters Table Type Port No Enter winipcfg and click OK. IP configuration window appears How to refer the network parameters from the PC Setting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Port Forwarding IP Masquerade feature Network Camera Access from the Internet If Top Page does not appear Top Operating Instructions Network Camera Screen and Setup Window Network Camera Flow Chart Top ExampleHttp//Global IP address of Broadband RouterPortNo Top Single Camera Motion JpegMulti-Camera Help ActiveX Controls Single Camera Screen Click to Center Pan/Tilt Scan, Pan/Tilt and Home Position Refer to Using Operation Bar On the table On the ceiling Using Pan/Tilt Operation Operating Instructions Zooming in and out Objects that are difficult to focus on by AF button Automatic and Manual Focusing Minimum object distance Setting Preset Positioning and Home Positioning Home Position Click Delete Deleting the preset buttons Viewing Buffered Image Screen Non Transfer mode Alarm/Timer mode Clicking Start Capture ViewerPrimary Secondary Multi-Camera Screen Viewing Images from Network Camera on TV Setup Setup Camera Setup AdministratorGo to Top Name/Time Reset to Factory Indicator ControlExternal Output Control Go to Top Network Enter only the number Instructions for the data fields Check Dhcp Dynamic Host Configuration Protocol If you use Network Camera on the LAN, set upSubnet Mask Mask File size of the image Ddns Camera Name/TimeName Date Time Changed AM/PM or 24H AdjustmentAuto Time Zone Click Security Administrator on Setup Security Administrator Enable For Setup PasswordRetype Security General User Click Security General User on Setup User ID List Delete or ModifyNew User Top View Image Instructions for the data fields Top ResolutionImage 160 x Image Quality Image Transfer Non Transfer mode Click Alarm on Image Transfer window Transfer in the Alarm Mode Alarm enable condition Sets the image resolution and image qualityActive Time of Trigger Over write setting Login timing Data transfer method Setting Example Setting explanation Transfer in the Timer Mode Buffers or transfers by the timer trigger Login timing Over write setting Camera Setup Suggested White Balance is also registered in preset programmingFocus Control Focus Control can be locked Having reached the selected end Specifying the Pan/Tilt range Click Save when finished Multi-Camera IP Address or Enable check boxURL * 1 or Host Camera Name External Output Control Click External Output Control on Setup Indicator Control Status Click Cancel to quit. The window returns to Setup RestartClick Restart Now Update Firmware Click Update Firmware Click Update Firmware on Setup Operating Instructions Reset to Factory Default Technical Guides Mounting on the Table Mounting Mounting on the Ceiling Wiring through a hole made in the ceiling Make a hole for a cable Wiring without making a hole for a cable in the ceiling Ceiling Mounting example Making holes on mortar wall Explanation of External I/O Interfacing to the External I/OPin Function External Sensor Input Circuit Diagram Example Unavailable character set Ascii and ISO-8859-1 Character TableSpace, , , #, &, %, =, +, ?, , and are not available For assistance, please call 105 106 Displayable character set Maintenance LensFor assistance, please call 107 108 Specifications and Troubleshooting Network Camera Reset Procedure-Default Settings Items Factory Default Indispensable setting Value Network Default Settings List For assistance, please call 111 Alarm 112 Items Factory Default Indispensable setting Value Alarm For assistance, please call 113 Items Factory Default Indispensable setting Value Timer 114 Setup For assistance, please call 115 Update Firmware Network Camera Specifications Description SpecificationsOther Specifications Description 116 Message Transferring Method When detecting the alarmOperation/Ethernet link Situation in Buffered Image Operating Instructions Troubleshooting About Network Camera SetupProblem Cause and Remedy LAN. Refer to For Indicator Control window Transfers older Network window on Update About Network Camera Setup Problem Cause and Remedy Click Tools -Internet Options -Security tab About Top View Image screen Cleaner Automatic Focusing feature. Clean the lens with lensManual focusing may be set. Press appropriate one Blurred images may have been registered when registering About Other Troubles View Image Setting window on Confirmation of Network Camera Operation Click the language to change the display FCC and Other Information 130 131 Index Operating Instructions TCP/IP When you ship the product For product service