Using the Belt Clip | Panasonic KX-TCD700BX instruction

31939_KX-TCD700CX_Czech 18/6/01 1:54 pm Page 49

4.Place the new option cover fitting the tabs on the cover into their slots on the handset.

5.Snap the option cover shut on the lower ➀, middle ➁ and upper ➂ parts of the handset.

Tabs

Slot

Slot

3

3 2

2

1

1

6.Connect the batteries and close the battery cover.

Using the Belt Clip

You can hang the handset on your belt or pocket using the belt clip.

To remove the belt clip

Chapter 5

46

Image 46

Panasonic KX-TCD700BX operating instructions Using the Belt Clip

Contents

Operating Instructions Charge the batteries for approx hours before initial use Accessories included Dear purchaser Safety Instructions Environment Contents Programmable Functions Useful Information On the Base Unit Programmable Functions On Getting Started Connection of Power SupplyConnections Battery Strength Installing the Batteries in the HandsetBattery Charge Battery Information Remember to charge the new batteries after replacement see Battery CautionBattery Replacement Getting Started Wall Mounting Base Unit Location of ControlsHandset Handset Display Symbols UsedDisplays Icons Basic Start-up Operations To Redial the Last Number Dialled Making CallsTo Dial after Confirming the Entered Number To Redial after Confirming the Numbers in Redial Memory To Edit/Clear Numbers in the Redial List To Select the Receiver VolumeMaking Calls Direct Call To Turn the Handset Ringer Off Temporarily Answering CallsAuto Talk Lighted Handset Keypad Storing Phone Numbers in Memory Speed DiallingDialling a Stored Number Speed Dial Menu S U to select no Saving Numbers in Speed Dial List save speed Speed DiallingDisplay number to be saved How Caller Information is Displayed when a Call is Received Caller ID ServiceChecking the Number of New Calls Caller ID Service Caller ID Sub-Menu Viewing the Caller List Using the Caller ListTo exit the list, Z W or P Calling Back from the Caller List Using the Caller ListFor Optional Multi-Unit Users Operating More than One Handset Intercom between Handsets Paging/IntercomPaging All Handsets from the Base Unit Transferring a Call from One Handset to Another Paging/Intercom Handset 1 Z P Handset 2 When the unit rings, Z O to answerConference Using the Recall Feature Special FeaturesHow to Use the Pause Feature Temporary Tone Dialling To Cancel the Key Lock Special FeaturesSetting the Key Lock on Y for more than 2 seconds Summary of Programmable Functions On the Handset To Stop the Alarm Setting Time Alarm FunctionSet Time of Alarm set time Ringer vol Set Battery Low Tone ON/OFF battery low on/off Setting Tone OptionsSet Range Warning Alarm ON/OFF range alarm on/off Set Key Confirmation Tone ON/OFF key tone on/off Select the Standby Mode Display standby mode Setting Display OptionsSelect the Talk Mode Display talk mode Set Call Prohibition call bar see Setting Call OptionSet Direct Call ON/OFF set direct on/off see Set Direct Call ON/OFF set direct on/off Select Battery Type battery type Setting Other OptionsSet Auto Talk ON/OFF auto talk Change Handset PIN hspin change Registering a Handset to a Base Unit register hs RegistrationHold Ï on base unit for 10 secs. a confirmation tone sounds Cancelling a Base Unit cancel base ZV or Y Specified Base Unit Access eg. base1 Automatic Base Unit Access autoSelect Base Unit select bs Reset Handset reset hs Function Initial Setting Programmable Functions On the Base Unit Bell Selection To Select the Dialling Mode To Select the Base Unit Ringer VolumeSetting the Clock Programmable Functions On the Base Unit Select Earth/Flash ModeSelect Pause Timing Cancelling a Handset Set Base Unit PIN Reset Base Unit Function Initial Setting Option Covers Using the Belt Clip Problem Remedy Before Requesting Help Outlet may be interfering with the Caller ID Adding Another Phone Before Requesting Help 28426English 13/2/01 358 pm 28426English 13/2/01 358 pm PQQX13170ZA KU0601LL0