NOTE:
BYou can also turn off the power by pressing the POWER button twice or by holding down it for at least 0.5 seconds.
BWhen the projector is in standby mode (the power indicator on the projector is illuminated red), the projector will still draw a maximum 7 W of power, even when the cooling fan has stopped.
BWhen the WEB STANDBY is set to “ON”, the cooling fan operates and the power indicator on the projector flashes slowly in red and the projector draw a maximum 30 W of power. (page 48)
BDo not turn off the power while the SD card is being accessed and “SD CARD IN USE.” is displayed on the screen.
Power indicator
Power indicator status | Projector status | ||
| Illuminated | The projector is in standby mode and image projection | |
| is possible by pressing the POWER button. | ||
|
| ||
|
|
| |
Red | Flashing | WEB STANDBY in the NETWORK menu is set to | |
“ON”. The projector can be controlled with personal | |||
| |||
| slowly | computers by means of a wireless network. | |
|
| (The cooling fan is operating.) : | |
|
| The projector is preparing for projection after the | |
| Flashing | power is turned on while the power indicator is | |
Green | illuminated red. (After a short period, a picture will be | ||
| |||
|
| projected.) | |
| Illuminated | A picture is being projected. | |
|
|
| |
| Illuminated | The lamp is cooling down after the power is turned | |
| off. (The cooling fan is operating.) | ||
|
| ||
|
|
| |
Orange |
| The projector is preparing for projection after the | |
| power is turned on while the power indicator is | ||
| Flashing | ||
| illuminated orange. (After a short period, a picture | ||
|
| ||
|
| will be projected.) | |
|
|
| |
RGB INPUT indicator |
| ||
|
| ||
RGB INPUT indicator status | Projector status | ||
Illuminated during | A signal is being input to either the RGB1 IN or | ||
standby mode | RGB2 IN connector. | ||
|
| ||
Illuminated during | A signal is being input to the connector selected | ||
projection | using the input select buttons. | ||
|
|
| |
Correcting keystone distortion and automatic positioning (AUTO SETUP)
This projector detects its degree of tilt and the input signal. Keystone distortion and the position of the image can then be corrected automatically in accordance with the input signal.
Press the AUTO SETUP button.
|
| (When the projected image has caused keystone distortion) | |
POWER AUTO SETUP |
|
| |
RGB | LASER | Screen |
|
VIDEO | MENU |
|
|
PAGE | Projected |
| |
image |
| ||
|
|
| |
|
| BAutomatic positioning | [ |
|
| will be carried out. |
|
Projector control panel
functions
Useful If you press the AUTO SETUP button, the items given in the table below will
be set automatically in addition to keystone distortion being corrected. The setting details change according to the signal which is being input.
Input signal | Contents set up automatically | Page | |
| POSITION, DOT CLOCK, CLOCK PHASE | 40, | |
RGB signals | (If the dot clock frequency is 100 MHz or higher, the DOT | ||
41 | |||
| CLOCK and CLOCK PHASE will not be set automatically.) | ||
|
|
|
NOTE:
BIf the edges of the projected picture are indistinct, or if a dark picture is being projected, the automatic setup processing may stop automatically before it is complete. If this happens, project a different picture and then press the AUTO SETUP button once more, or make the above adjustments manually.
BSet AUTO KEYSTONE in the OPTION menu to “OFF” to prevent any deterioration of the picture as a result of keystone correction. (Refer to page 45.)
BKeystone distortion may not be corrected enough depending on the adjustment of the zoom ring. In this case, adjust the KEYSTONE option. (Refer to page 41.)
