Making the wireless link
1Turn on the wireless system.
Wireless unit on/off button [POWER C I, B Í]
Use this button to turn the unit on and off.
C I: The unit |
| is on. | B Í: The unit is off. | ||||
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
POWER WIRELESS LINK
WIRELESS LINK indicator
Red: The unit is on and the wireless link is deactivated.
Green: The unit is on and the wireless link is activated.
2Turn on the main unit.
The wireless link indicator on the main unit will be turned on.
e.g. |
|
|
|
| ≥If the indicator is flashing, refer to the |
SLP STCT | DDTS PL | |
| SRDE. PRG | “Optional wireless system |
PGMRNDRDS | the Troubleshooting guide. (> 46) | |
EQ | W1W2 WS |
For 4.1 ch settings, go to step 8.
3Turn on the additional wireless system.
4While pressing [5/9] on the main unit, press the numbered button [3] on the remote control until “P” lights in the main unit’s display.
5 While “P” is displayed, press | I/D SET | |
[I/D SET] on the rear of the | ||
| ||
additional wireless system. | Use a pointed object. | |
≥The indicator on the additional | ||
system turns green. |
|
≥If “P” goes off before you press [I/D SET], repeat step 4 and then continue the procedure.
6While pressing [5/9] on the main unit, press the numbered button [3] on the remote control.
7Turn off and on the additional wireless system.
≥Make sure the indicator on the additional wireless system lights up green.
8Start the EASY SETUP to configure the speaker settings. (> 12)
≥After changing the speaker settings start play on the main unit.
≥The main unit will not recognize the additionally added speakers unless the speaker settings have been
SETUP. (> 12)
– Be sure to
NOTE ≥If you should change the digital transmitter, repeat the pairing steps of the wireless system.
– If 2 wireless system units are used, repeat the pairing steps for each unit, 1 at a time. ≥You cannot use the wireless system with
Speaker installation options
Attaching to a wall
You can attach all of the speakers (except subwoofer) to a wall.
≥The wall or pillar on which the speakers are to be attached should be capable of supporting 10 kg (22 lbs) per screw. Consult a qualified building contractor when attaching the speakers to a wall. Improper attachment may result in damage to the wall and speakers.
1 Drive a screw (not included) into the wall. |
|
|
| e.g., Front speakers | |||
|
|
|
|
|
|
| |
| At least 30 mm (13/ | 16 | ) | DO | |||
|
|
|
|
|
| ||
|
|
|
|
|
|
| |
4.0 mm (5/32) |
|
|
|
|
|
| NOT |
7.5 mm to 9.4 mm |
| ||||||
|
| ||||||
| (19/ | 64 | to 3/ | ) |
|
|
|
Wall or pillar |
| 8 |
|
|
|
| |
3 mm to 5 mm (1/8to 3/16) |
|
2 Fit the speaker securely onto the screw(s) with the hole(s).
DO
In this position, the speaker will
likely fall if moved to the left or right.
Move the speaker so that the screw is in this position.
Preventing the speakers from falling
≥You will need to obtain the appropriate screw eyes to match the walls or pillars to which they are going to be fastened.
≥Consult a qualified housing contractor concerning the appropriate procedure when attaching to a concrete wall or a surface that may not have strong enough support. Improper attachment may result in damage to the wall or speakers.
e.g.
String (not included)
Thread from the wall to the speaker and tie tightly.
Optional speaker | settings |
|
|
| Approx. | |
Screw eye |
|
| 150 mm | |
Wall | ||||
(not included) | (529/32) |
Rear of the speaker
RQT9479
43